LGD912 (P7804820W W) Amana Dryer - Instructions

Door switch was very easy to replace as it simply snaps in for the outside and you just clip on the two control wires that already have clips on them.

took 2 screws out and replace new coils

All you need for a Maytag is a snub nose Philips screw driver. The screws on the front panel are at the bottom angled down, so a regular length Phillip's won't work. Just unscrew the 2 screws, then lift the panel up and out. Careful not to pull out too far, there are 2 wires attached to the switch. The replacement switch is NOT an exact copy of the old one. My Maytag is over 30 years old and it only had 2 prongs on the switch. The new one has 3. Don't let that throw you. It is the same size. Just attach, 1 wire to the bronze connector & the other to the silver. Push the switch into the door opening, re-attach the door. Total time 20 minutes. Saved well over $100 in a service call. Anyone with an IQ above freezing can do it.

watched video for Each Part

My gas dryer would run with heat for 5 minutes in all settings, but kick off and not heat again. Timer would not advance in autodry. Thought it was the cycling thermostat, so replaced that, but did not solve the issue. Ordered the coils, and cleaned out heavily clogged lint from bottom of lint trap, especially right above the fan motor at the bottom of the trap. Received the coils, opened the top and front, took out drum, and replaced the coils. The replacement took less than 2 minutes. Be careful putting the drum back on to make sure the felt is not caught inside the drum. You can give it a spin to make sure. Wear gloves, as I cut myself up pretty good on the edges of the dryer body. The inside of my dryer looks like a crime scene! Anyway, I put it back together, and it runs great. Solved the timer advance issue in autodry, and the heat kicks on and off when it is supposed to. Good luck! Thanks Part Select!

Watched youtube video to problem shoot. Cause determined to be coils bad. Searched web found Parts Select to be easiest site to deal with and had coils for best price. Followed instructions supplied with parts. Dryer works like new.

Unable to find a repair manual or accurate diagram, I forged ahead and removed the top and front panels of the dryer. It took two tries to figure out how to thread the belt (nine of my ten thumbs kept getting in the way!), but after a coffee break, the job came together, and I've taken the clothesline down!

i read some of previous customer problems and fixes pulled the front cover off found coil's location when i turned on drier you could see the ignitor getv hot but burner would not ignite unless i put a little pressure on secondary coil when i let go of coil flame would go out. ordered 'M' series new style coil kit came in in about three days installed parts drier workng good i would reuse parts select agian thanks

Propped the machine up in the front, removed the front panel, the door assembly, and the front drum support. Use a Sharpie to mark wire positions. This will help during re-assembly. To get the drum out, you first have to remove the belt from the motor pulley. Drum slides right out. You will need snap-ring pliers to remove the pulley from the idler arm. I also replaced the drive belt because it was cheap, and always a good idea to replace it when you are this far into the machine if it is a few years old. Re-assemble in the reverse order of disassembly. An easy fix for the average do-it-yourself person.

After removing the lower access panel, I observed the drum and belt and saw it turning freely. The support rollers in the back turned freely and were in good condition as well. At odd intervals the unit made a humming or grinding noise, and i decided to check the blower wheel (the other rotating part in the system). I found that the central hub of the wheel (which is made of a nylon like plastic) had sheared off from the wheel itself. I ordered a new part and started to remove the old wheel. **NOTE** many of the stories I read described how this part would have a reverse thread, it did not and that cost me an extra 30 minutes to figure out (the new part had arrows showing the correct direction to put on and remove - the original didn't). Once everything was cleaned and reassembled, I started the dryer again, but got no heat. I had previously replaced the heating element, so I thought my wiring was wrong. That wasn't the problem, but a hint from this site about checking the incoming wiring was the solution, my ground wire had come off the terminal in the back of the dryer and I wasn't getting the volatge across the element that it required. With the ground wire back in place, everything worked fine.

I removed the two spade connectors and then removed the two 1/4" hex screws. I then simply removed the defective unit and replaced it with the new on and re-installed the two screws and wires.
This was not the problem though.
I turned out to be the solenoids on the gas valve.

Really an easy fix. 2 5/16" screws hold the cover on below the dryer door. From here it's easy access to the gas element. 2 more screws for the valve cover and disconnected the attached wires to the gas coil valves. slip the news ones in place, re-attach the wires and install the holder.Tested the dryer and it fired right up. Put panel back in place and the wife is happy it didn't cost us more than just the parts. Yep, she's a lucky girl. ;0)

As many of the other posts here on this website mentioned, I had the same problem of the dryer not heating up. I removed the front panel (4 screws on each side inside of door - easy - followed instructions) and once off I was able to view the igniter glowing properly so I knew the starter/igniter was not the issue. Everything I read then suggested that it must be the two terminal gas valve coil, and sure enough it was. Ordered part -- got it in literally a couple days -- removed bracket (two screws) put in new coil -- turned it on -- works great. Could not have been easier. This is a great website and would recommend it to everyone who is a Do It Yourselfer.

Per instructions I printed off online: took off door, then the front panel. Pulled out the old switch/button, connected the new switch/button, made sure the new button was working; put the panel back on then the door and DONE!

Found on your site the top two causes of a Dryer not getting hot enough and ordered those parts ( which were delivered quickly).Removed the top two screws that hold the front of the dryer that gives access to the coils and flame sensor assembly after lifting up the top.It took more time to clean up all the lint than to replace the parts.Dryer works great!