P1122704WL Amana Dryer - Instructions

Followed directions from Youtube video

Removed the screws on the dryer vent and the back of the dryer top. Then I raised up the top panel and removed the screws that held the front panel on. I removed the front panel to access the coils. I replaced the coils and then the front and top panel and screws. All went well. The dryer is working properly now.

I followed the online video on PartSelect website. No other instruction necessary.

Open top of dryer, then remove front. Coils on lower left. Unplug and replace coils. Vacuum loose lint from bottom of dryer. Replace front then top of dryer. Test run. All good !

rts came quickly & I got started. First, I unplugged the dryer and pulled it away from the wall about a foot. this was done so the top would have clearance when it was lifted up. Next, I removed the lint trap and then took the two screws under the lint trap door out. Then you use a screwdriver(flat blade) to release the top of the dryer. The release points are about 1-2 inches from the edge of dryer. Next pull the wire connector apart so the front can be removed. The connector is on the right side, front corner, facing the dryer. There are two hexhead screws near the top on both sides. Remove the and the front will come apart as you lift it slightly. Then you disengage the tub belt. Once this is done the tub can be lifted out and set aside/ take care to remember each things position as you take it apart, so you will not get confused when you reassemble. Now the solinoid assembley is easy to get to. Use a phillips screw driver and remove the two screws that retain the bracket that holds the solinoids in place.. Lift the bracket and remove one solinoid at a time. Pull the wire from it and plug the new, like solinoid to the wire and put it back in place. then do the other one. set the bracket back over the new kit and replace the screws to the bracket. Set the tub back in, rethread the belt to the drive wheel. Next put the front back on making sure the bottom part slips into the two sides of the dryer.Replace the hexhead screws on each side; plug the wire connector together. Now , pull the lid down into position and press into place. Replace the lint trap screws and replace the lint trap. Plug dryer up and we are done. Repossition the dryer to its original place. It really was not a hard job at all. Thank-you Susan for your help and expertise.

I totally disassembled the Dryer, and replaced the Guide Rollers, Blower Wheel, Idler Pulley Shaft, Idler Pulley, and Belt.

I unplug the electric, close the gas valve, use the putty blade to prize up the top,unplug the electric horness, took the front door off, took the anker plate off the two coils, removed the wire from each coil,be careful not toget the wires mixed up one coil has two proms and the other has three proms after that u put everything back together the way u took it off!!

Disconnect power. First, remove the lower front panel, then the upper front panel (disconnect door switch wiring). Remove two screws holding the top panel to the left and right side panels. Remove wiring connections to light and humidity sensor. Remove four screws to front drum support assembly, lift up to disengage tangs, and remove assembly. Reach in and find the idler assembly for the drum drive belt, and unwrap the belt to loosen it, also removing the belt from the motor pulley.. Slide the drum out the front of the dryer along with the drive belt. Remove the snap ring (using snap ring pliers) and washer holding the idler pulley on to the idler assembly. Remove the idler pulley. Polish the shaft with fine steel wool to get rid of dirt. Clean thoroughly, leaving no steel wool residue. Install replacement pulley, washer, and snap ring. Reinstall drum, taking care to feed belt back into place as the drum is reinstalled. Reach in and wrap the belt around the motor pulley and the idler pulley. Reinstall the front drum support by lifting the drum slightly to allow the support to engage with the drum, and then drop it down to re-engage the tabs into the left and right side panels while reseating it into the blower intake. Install the four screws to hold it in place, and reinstall the wiring for the light and the humidity sensor. Attach the top panel to the left and right side panels with one screw for each side. Reinstall the upper front panel, including reattaching the wiring to the door switch, with two screws. Finally, reinstall the lower front panel. Reconnect to the power source, and you should be good to go.

remove front of dryer with door to get to the back of lach pin. replace front. seprate innor and out door pieces use pliers to remove catch spring clamp ot replace catch screw innor and outor doors back togfther and put tools away your done

i removed the door and front panel then removed the two screws holding the coil bracket,disconnected the two wires on coils,set new coils in place and reversed the above process

I shut off the power supply (pulled plug) . Opened the front access door on bottom of dryer, The two coils sat on top of burner unit, with a plate and 2 Phillip head screws securing them. .I used a small set of pliers to pull the terminals off, then I used a short Phillip head screw driver due to the proximity of the dryer drum close by. The coils slide off, slide the new ones on, re secure the plate with screws, reconnect the terminals, plug in the power cord and away you are for a fraction of the cost.

First we removed the front panel then the door. Removed the old coils and put in the new coils, oh yeah don't forget to disconnect the power supply first. Sure enough that was all it took and it runs great. You really can fix your own appliance if you take the time to do some research.

Unplug dryer. Remove lower panel.Remove dryer lent duct. Remove Thermostat fm fan housing. Remove Fan.Remove Fan housing. Remove Motor assy by sliding out, wires lay toward front, allowing room to replace idler pulley and spring. Use lock ring pliers to remove pulley from shaft. Grease pulley/shaft w/high temp grease [I used ultra-hi temp ceramic brake grease-can get in small packets at auto stores].Noise/slippage has all but stopped. Lesson: replace rear rollers and front felt/glides. Belt looseness also caused by worn rear rollers [smaller overall diameter from age]-even though they spin freely

My husband pulled drum out of dryer and replaced the idler pulley wheel and decided to replace the belt while he was in there. It's good to have a snap ring tool as it's a pain to replace the snap ring without this tool. Goes alot quicker!

DISCONNECT THE POWER. (I got shocked a few times during the diagnoses stage). Remove the lint catcher. Pop the top of the dryer up (there are two plastic tabs along the front of the dryer. Remove the two screws for the lint catcher and open the top of the dryer. Loosen the screws between the side and front panels. Lift up on the front of the dryer to free it from the clips down below. Swing the front panel out of the way to avoid disconnecting the door-open-switch. Undo the two screws holding the bracket onto the gas burner regulator. Replace the coils. Reassemble in the reverse order. It was helpful to open the dryer door to help align the drum and front panels.