P1122702WL Amana Dryer - Instructions

Being my lousy Maytag washer died THE PREVIOUS DAY, spewing water, etc. and I had rushed out and bought a new washer, I was determined not to replace the dryer (though I now am a serious NON_FAN of Maytag).

I disassembled the whole dryer and finally got to the blower wheel which was broken lose from the molded nut. I supposed something like a dime or penny got in there to shred it.

PartSelect's website allowed me to find the part in 5 minutes. It was on my doorstep the next afternoon.

Installation was straightforward BECAUSE I stacked all the screws and and labeled them appropriately. It took about 30 minutes to reassemble and the toughest bit was getting the drum in with the belt positioned properly.

Removed power and front panel, removed broken latch, pushed in new latch and replaced the front panel and power. Done

discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!

First unplug the dryer,then remove the front bottom panel. With your 5/16 nut driver reach to the rear of the vent tube under the dryer and remove the lone screw that holds the tube in place. Lean the dryer forward and remove the tube from the rear of the dryer,this will allow you to see and reach the idler wheel from the front. Release the belt,feel for the clip that holds the wheel in place on the opposite side of the front,with your thumb nail or something else if preferred pry out on one side of the clip until it pops off. Slide the wheel off being careful not to lose the washer,slide the new wheel on and replace the clip. Put the belt back on replace the tube,which is actually the toughest part because you have to find the hole for the lone screw as you can't see it,but with a little patience it is easily enough done. Put the vent hose back on replace the front panel and plug it in and go!!it took me 30 min. Alittle tough to feel for some of the parts,but really much easier than you would think.

I took out the old worn out part and replaced with the one I order.

Very simple repair. Remove front panel, door, drum etc. Try to keep everything seperated, screws etc. I put lockjaws on the back to get the nut off the front. Make sure to check the housing for "melted on" blower wheel residue. Easy enough to remove. I checked with my local parts dealer he wanted twice the price and needed to order it (at least a days wait). PartSelect sent the exact same part in a day and a half. Put everything back the same way I removed. Hardest part is the drum and belt. While you have everything apart don't forget to clean the thermastats etc. PartsSelect was quicker and cheaper.

My son will discribe how he did the repair.
First I opened the top, then I removed the front with a 1/4 inch ratchet and socket. I took the cover off the blower housing with a nut driver. Used the appropriate socket and a 1/2 inch ratchet, and an adjustable wrench to hold the motor shaft and removed the Blower wheel. I replaced the broken Blower Wheel and put all it back together.
Our dryer is now working great and there are no unwanted sounds emanating from within. We are very happy with PartSelects promptness and that we recieved the correct part as ordered. PartSelect website was easy to navigate. We plan if the need arises to do so again in the future.
Thankyou Frank and Rodney

After watching the great install video, I followed his lead and within 20 min had my dryer door fixed. This dryer was bought in 1986 and I really thought I was looking at buying a new dryer. How wonderful that I could fix it for less than $11. Easy to find web site, easy to find part, great instructions and fast delivery!

The front of the dryer needed to be taken off, the drum needed to be taken out and the belt installed on the wheel structure.
I was very pleased at how fast I received the part after ordering it! I will definitely use this site again when ordering replacement parts!

remove front of dryer with door to get to the back of lach pin. replace front. seprate innor and out door pieces use pliers to remove catch spring clamp ot replace catch screw innor and outor doors back togfther and put tools away your done

Disconnect power. First, remove the lower front panel, then the upper front panel (disconnect door switch wiring). Remove two screws holding the top panel to the left and right side panels. Remove wiring connections to light and humidity sensor. Remove four screws to front drum support assembly, lift up to disengage tangs, and remove assembly. Reach in and find the idler assembly for the drum drive belt, and unwrap the belt to loosen it, also removing the belt from the motor pulley.. Slide the drum out the front of the dryer along with the drive belt. Remove the snap ring (using snap ring pliers) and washer holding the idler pulley on to the idler assembly. Remove the idler pulley. Polish the shaft with fine steel wool to get rid of dirt. Clean thoroughly, leaving no steel wool residue. Install replacement pulley, washer, and snap ring. Reinstall drum, taking care to feed belt back into place as the drum is reinstalled. Reach in and wrap the belt around the motor pulley and the idler pulley. Reinstall the front drum support by lifting the drum slightly to allow the support to engage with the drum, and then drop it down to re-engage the tabs into the left and right side panels while reseating it into the blower intake. Install the four screws to hold it in place, and reinstall the wiring for the light and the humidity sensor. Attach the top panel to the left and right side panels with one screw for each side. Reinstall the upper front panel, including reattaching the wiring to the door switch, with two screws. Finally, reinstall the lower front panel. Reconnect to the power source, and you should be good to go.

i removed the door and front panel then removed the two screws holding the coil bracket,disconnected the two wires on coils,set new coils in place and reversed the above process

My husband pulled drum out of dryer and replaced the idler pulley wheel and decided to replace the belt while he was in there. It's good to have a snap ring tool as it's a pain to replace the snap ring without this tool. Goes alot quicker!

First we removed the front panel then the door. Removed the old coils and put in the new coils, oh yeah don't forget to disconnect the power supply first. Sure enough that was all it took and it runs great. You really can fix your own appliance if you take the time to do some research.

I shut off the power supply (pulled plug) . Opened the front access door on bottom of dryer, The two coils sat on top of burner unit, with a plate and 2 Phillip head screws securing them. .I used a small set of pliers to pull the terminals off, then I used a short Phillip head screw driver due to the proximity of the dryer drum close by. The coils slide off, slide the new ones on, re secure the plate with screws, reconnect the terminals, plug in the power cord and away you are for a fraction of the cost.