LEA50AW (PLEA50AW) Amana Dryer - Instructions

Open bottom panel and observed back left drum roller wheel wobbling and obviously making the loud rumbling banging sound. Search goggle for Amana model part -- found partsellect.com, and read the list of other DIYs:

Take off the lower and upper front panels (two screws
each);

Remove the front drum glide holder (four screws. Careful
here because of the two wires to be removed for
door open off switch;

Pulling drum forward only enough so the bad roller wheel
would come off shaft after removing shaft snap ring
keeper;

Grease new roller hole and old shaft then place the
new wheel roller on shaft;

Replace all items back after cleaning lent off.

Note: Snap ring was a bit tricky (need snap ring pliers)--make sure it is clipped back all the way on the shaft after new wheel is installed. Also, I thought it was a good idea to put something underneath the dryer drum to support it while it was slightly pulled out -- a block of wood, etc. I found a spot remover plastic bottle that wedged up to support the dryer drum enough to take pressure off the belt during wheel replacement.

Ordered new lint filter, which did not quite fit. Called company and was told that filter had been redesigned to remove the felt surround, and that sometimes the new filters did not seat well. It turned out that the exhaust pipe was filled with packed-down lint causing the new filter not to go all the way into the slot. My husband surmised that that was why the first filter broke because volunteers at the Humane Society adoption center were trying to shove the filter into a groove that no longer worked. He took off the top, the front, and one other piece before removing all of the lint he could reach. Once that was done, the filter fit fine.

first i checked the power supply then i checked each of the switches and limit fuses for continuity.
to do that i had to take the front of the drier off, four screws there. then i removed the bad limit switch 2 screws,the door switch was bad so i replaced it, no screws. since i had the front off the drier i removed the four screws that held the drum in place and replaced the belt. assembled the drier in reverse order when the parts came. 1/2hour total labor.

I first removed the two front screws on the front cover located on the lower half of the dryer using a flash light looking on the left side all the way to the back you will see two hex screws removing them will now let you wiggle the heating element back & fourth while pulling down it will come out in just a few seconds - then with your digital camera take a picture of the still wired heating element as to a clear reference for wiring the new element - first Aline the new element in the same direction as the old element and transfer them one by one check camera for assurance that you have done it correctly and re-reinstall in the reverse order

also I would recommend taking off that black plastic blower chute and cleaning it assuringly the best performance of air flow

Removed bottom door panel, four screws. The new part was a slightly different (looks like improved) part, so only had to put two screws back in. Very simple. The only reason it took more than 15 minutes was because I cleaned exposed areas while the panel was off.

I inserted the clip

1. I removed the lower front panel.
2. Carful remove the front door making not of which wires whent were of the switch
3. Removed the front bulkhead.
4. Drilled out the rivits that held the bracket in place.
5 Use a pop rivit gun and 1/8 in pop rivit and washer.
6 Installed the felt pad and the drum guide.
7 Put the whole thing back together.

I love your web site the exploded diagrams make fixing my dryer quite easy. I do it. so for under $50 my dryer is almost like new.

After removing the front of the dryer, I took out the front assembly where the seal and glide brackets attatch. I replaced the bad cylinder glide by drilling the old rivets out and re-riveting the new glide in place from the back side. I then replaced the felt pads and glides on the glide brackets and glued a new cylinder seal around the front assembly. I reccomend having 4 hands for placing the cylinder seal around the assembly with fresh glue.

First, leaned dryer back and removed 2 screws at bottom front panel.
Then removed 2 screws at bottom of door assembly.
Pulled bottom door assembly forward and down.
Disconnected "can't go wrong" wiring connectors.
Then removed old cylinder glide rivets at bottom of cylinder using drill motor with 1/4" drill.
I installed new felt pads on new cylinder glides. Then installed glides with rivet gun.
Reconnected wire harness.
Installed door assembly and lower panel assembly.
BACK IN BUSINESS! THANK YOU!!!!!!!!!!

Not too difficult. Take out of box, insert into dryer slot.
Done

Remove the 2 screws at bottom of front panel, remove lower panel. Then remove the two screws at bottom of front door. Lift door forward so spring hooks can disengage from the top panel. remove door, disconnect the 5 wires to the door latch and light. remove the two screws at top of dryer to lift up top panel. Remove 4 screws at the front holding the drum. Disengage the belt from the tension pulley and remove drum. Replaced both roller wheels at the rear of the drum( one was broke). Then remove the screws (about 6 holding the plate in front of the blower wheel. Use a wrench to hold the nut at the back of the motor and a scocket wrench to remove blower wheel. (The Blower wheel was broken from the shaft and was spinning freely). Then do it all backwards to re assemble. i spent more time cleaning the lint from the inside than I took making the repair!

Shut off or unplugged dryer for safety.

Slipped thin blade putty knife up under bezel of switch to unlatch from the panel and pulled forward to remove the swwitch from the dryer. Unplugged the quick connect terminals (3) from the old switch and plugged them onto the new switch. one of the terminals had gotten quite hot and darkened the insulation so it was replaced with one that was supplied with the switch. that was a cut, strip, crimp process. Placed the new switch into the panel and snapped into place.

First I turned off the circuit breaker, then removed the two screws that hold the front lower panel in place. Once open I removed the 2 screws that held the element in place. (Far back left side) I then pulled the element out leaving all wires connected. Wires are long enough to extend out to the floor in front of the dryer. I simply exchanged the wires one at a time to the new element so no mistakes could be made. Reinstall, reset the breaker, and Instant HEAT. Repaired for under $40.00

remove bottom section under door 2 screws remove door 2 screws remove switch by squeezing tabs install 2 new female ends on wires supplied with switch . put switch back in plug in wires .

Determined that the 2 completely worn off front & rear drum seals were causing dryer to take too long to dry clothes.
Removed the front bottom panel first, then the middle panel and then the top panel. After removing the belt from the drum, it came out easily. Replaced both thermostats and fuse
just so they would be new in the unit.
Reglued the seals in place and waited til glue dried. Then reassembled everything back. Also lubricated the drum wheels. Everything worked and was quiet!