LE4207W2 (PLE4207W2) Amana Dryer - Instructions

Pulled the big front panel by removing two screws near bottom of front and pulling out at bottom until the top pops loose. Vacuumed out all of the dust and checked for loose connections. Ran dryer - igniter would light, but no gas. Checked the two solenoids with a VOM. the one with the two leads would intermittently read Infinity (open). Super simple repair. Remove two screws on solenoid bracket on top of the gas valve, Replace solenoid and plug it back in with the easy push-on connector. NO PROBLEM - all fixed.

I removed the front panel of the dryer by removing the 2 screw that secure it at the bottom and pulling upward to disconnect the cover at the top. I then removed the two screws that hold the metal cover that secures the 2 elements in place. I disconnected the wire plugs from the 2 elements, removed the 2 elements and replaced them with the new parts making sure to place them in the same positions as before. I then replaced the housing cover and tightened the screws. Then I replaced the front cover of the dryer.

removed the dryer female part that was broken with needle nose pliers and inserted the new one, on the door i removed one phillips screw and r/r the male piece with the new one and re-inserted the screw. that was all, very easy repair

Because the wheel had stopped and the shaft kept turning (junk from child's pocket got in there), the nut stripped itself away from the wheel causing low RPM and low air movement (lazy flame, vibration and clothes not drying)

I had to use a screwdriver to break the wheel away from the center nut and remove the fan. I then removed the air fan housing (3 bolt behind the fan wheel). I used a small pair of vise grips to hold the motor shaft staionary while I used a pair of channel lock pliers to remove the nut that was molded into the fan from the motor shaft. It was harder to get the nut started then I would have thought.

Once complete, I put the fan housing back on and threaded the new wheel on easily. The motor has external fins on it which turn with the shaft-I held one lightly while I threaded the fan on to keep the shaft from turning. Tighten just slightly more than hand tight-don't go crazy-it's threaded to stay tight with rotation. Works great and very quiet now.

First removed the bottom access panel, then the then pried the top lid open. Then, I could get to the four screws holding the front of the drum in place. Once that was removed, reached underneath drum and disconnected belt from tensioner pulley and motor. Removed the drum and discovered the problem. One of the two drum rollers had completely disintergrated from the shaft, actually "melting" off of its roller shaft. Removed both of the rollers and shafts by putting a flathead screwdriver on the slot of the shaft, and at the same time holding the locknut behind the bracket with a box wrench. I replaced both shafts and rollers and reused the same washers and snaprings. I used a screwdriver and a vice to remove the snap rings off of the old shafts. The best bet is to use a pair of snap ring pliers, which I didn't have. I used some white silicone grease to lube the new rollers up, reinstalled them and replaced the belt. You MUST route the belt around the drum before you install, then connect the belt to the motor underneath and wrap it around the tensioner. While I had everything opened up, I shop-vac"d the inside of my dryer(filthy). I did this before putting anything back together. Also, when re-installing the front dryer panel, make sure the motor inlet and the lint outlet tube form an airtight seal. All in all, this was a fairly strightforward job. The dryer now works great and is as quiet as a mouse.

This was the second time we lost the High Limit Thermal Fuse. My wife dried some new towels and the lint filter completely plugged before the cycle was done and popped the high limit fuse. I went throught this before and paid a fortune for a repairman and ended up installing the thermal fuse myself so I did it myself and saved about $100. I also ordered an element kit so I have it. I will just swap out element units if there is a next time. Maybe the next time we buy new towels. It only takes few minutes to remove the front lower panel and unplug two wires, remove two screws and the element assembly with both the fuse and the thermostat are out. It is easy to replace the fuse with the element assembly in your hands and in good light.

I just inserted the door catch, which by the way fit in perfectly. Thanks. Took 5 seconds to repair.

The pully wheel was completely worn down as the belt had cut into it over time. I'm not sure if the lever and shaft needed replacing but since the part was inexpensive I decided to replace it as well as the wheel. The easiest way to access the parts was to turn the dryer on its side and remove the bottom panel of the dryer. This eliminated the need to remove the drum. It was then easy to reach in with a wrench and remove nut and bolt that held on the pulley lever. I also had to remove the spring which was attached to the lever. Next I put the new pully wheel on the shaft of the new pulley lever. The most difficult part of the job was installing retainer clip which holds the wheel on the shaft. This took a little persistance. After this was done it was simple to put the assembly back in place, reattach the spring and tighten the nut and bolt. I then replaced the bottom panel of he dryer, turned it upright and plugged it in. The whole job took just over an hour. One tip: Before removing the old assembly, I took a picture of it with my cell phone camera so I would remember how it went back together.

Dryer drum stopped but all other elements seemed functional; couldn't afford new dryer. Unplugged appliance & moved it to my garage (more room to move about). Undid base plate w/tools and found belt slack - identified broken idler pully wheel as part to fix. Went online & found part-select, located part & was way happy: $7.00 part + $7.00 shipping; got part 3 days later. Removed broken pully wheel (take off lock-washer, put wheel on, reinstall lock washer). Cleaned out venting elements (huge lint-ball & some sand in blower intake area). Re-attahced base. Back on-line to see "replace dryer belt" instruction sequence; opened lid of machine (while verticle) and positioned belt properly. Located access port (sealed) at base, knocked out the circular metal plate so I could reach in & thread the dryer belt back around motor & idler pulley wheel. Did test spin (manually) to make sure belt properly threaded, in place. Move appliance back to proper location, plugged in & hooked up venting to outside; ran test & SUCCESS!!!! It even seemed to dry better because of the now cleaned venting area. Labor cost = $0, Part cost < $15.00, Time (actual work) bit over 3 hours total.

Opened front panel .Tested both coils on gas valve.
Found no continuity on one of the coils. Replaced coil,
dryer works like new.

I opened the front panel and removed the heating element from the rear of the dryer by removing the two screws that held it in place, and slid the element out. using a mulitester I checked the High limit Fuse and it was not working.I ordered the part and replaced it. Everything worked great for two days and the dryer stopped heating again. My brother asked if I had replaced the thermostat because something burned out the fuse. He was right. I ordered both parts and replaced them. Every thing is working just fine. Save some money and time by replacing both parts at the same time.

Took out two front Panel screws and removed the panel. Removed Gas solenoid coil holding bracket by removing two phillips head screws. Disconnected the coil leads. and removed the coils. Connected the new coils to the leads and set in place. Replaced the holding bracket and the two screws. Replaced the front cover and the two front cover screws. Piece of Cake!

Switch can be removed from outside of dryer and your video described the repair as having to work from inside dryer. But since wires were still attached to old switch, it could be popped out and wires switched. Since there were three wires on new switch to allow it to turn on and off a circuit, it was useful to check the resistance of the switch compressed or released to be certain I was attaching the two wires to the right two poles of the new switch. But that all required only a couple of minutes. Thank you.

I removed the dryer front and the drum, then disconnected the wires from the dryer motor and removed it from the motor mount, after installing the new motor in the motor mount the rest was just putting the dryer back together the same way I took it apart, the best way to do this is to print out the diagram from partsselect.com and follow it step by step, this was so easy everybody can do this and save alot of money for the labor and the parts mark-up, try it you all can do it (SO EASY)

Unscrewed 4 screws,pulled off front of machine.Unscrewed 2 screws holding coils on,unplugged coils,installed new coils,plugged in coils,reinstalled 2 screws for hold down brace.Reinstalled front cover,plugged dryer into outlet(remember to unplugged dryer before working on it).started up,instant heat,works great.thanks Partselect for helping me out!!!