LE8567W2PLE8567W2 Amana Dryer - Instructions

As it turned out, the felt was only part of the problem. The guide bracket had been cut thru by the drum. This all started when a golf tee got stuck in the drum area. It took very little time to destroy the guide bracket. Dryer was built by Whirlpool. Parts are built to the bare minimum. These appliances are designed to break in a couple of years. There is no doubt about it. I installed the new guide brkt, glued the new felt on and put it all back together. The job is pretty straight forward but you need to be mechanically inclined.

I first removed the front panel and door on the dryer using a 5/16th nut driver. I needed to disconnect the light and switch to remove the door. I raised the top lid of the dryer to expose the drum. I rmover the fan schroud and lint filter by removing 4 5/16 screws with the nut driver. I disconnected the belt from the idle tension pully and removed the drum. The drum support rollers were visible on the back frame of the dryer. I removed the bad roller using snap ring pliers. After cleaning the roller support shaft and lubricating the shaft with grease I replaced the drum support roller and secured it with the snap ring. I also replaced the dryer belt although it was still workiing. I reasembled the dryer after giving the inside a cleaning with the shop vac. The hardest part was getting the belt secured with the tension idle pulley. When assemblying the fan schroud make sure it is snug against the fan so it doesn't leak. Replace the top and front door and cover connecting the switch and light. If you get the switch wires correct the dryer will run with the door shut otherwise reverse the wires.

I took out the 2 screws on the bottom of the front cover, pulled out at the bottom, disconnected the 2 wires for the front door and removed 2 screws on the inside top of the front panel and removed. The top of the dryer then flips over. I then tool out 4 more screws and took out the drum. I totally cleaned out the inside of the dryer and then took the oring pliers and removed the oring that held the roller on the belt tension bar and replaced it with the new one that you sent me. I put the drum back in and put the belt back on the new roller, I put the dryer back together and now I have a good dryer that will last another 10 years.

I guessed that a new belt may fix the problem. The repair was nearly as easy as the video suggested. I believe the dryer had been repaired before since there was a circular panel on the side which had been removed. I could reach in through the side to slip the new belt onto the pulley. The new belt now enables the drum to turn even for heavy loads.

This dryer is an older one. I have kept it running throughout the years by just replacing parts a needed. This was a kind of rebuild. The dryer was making that squeaking noise when running so I knew the "glides" were worn and the belt, rollers and idler pulley had never been replaced. I ordered the parts from this website and I must say it took a while for them to ship, of course I guess since it was during the holidays that's to be expected. Once I received the parts I took the dryer apart. This model has a lower panel that comes off first then there are two 5/16" sheet metal screws that hold the door panel in place and then two more to hold the top down. Then I removed the front bulkhead which holds the drum glides. I replaced the glides then removed the drum from the dryer. To removed the motor there are two 5/16" screws to removed then pull the motor from the bottom. I then replaced the idler pulley, the two drum rollers on the rear of the dryer and the belt on the drum. Reassembly went fairly easy. I found the door switch was bad during reassembly because the dryer would not shut off once the door was opened. So picked up a new door switch from a local supplier, replaced it and all is good now. There really isn't that much to a dryer. A motor, heating unit (in the rear), control unit/timer on top, and then the rollers, idler pulley, and drum belt. The video instructions on this website were quite helpful. Hopefully it will last another year.

The Dryer is about 25-30 years old. I replaced the motor due to overheating, while I had the dryer disassembled I decided to change out the idler pully wheel and the drum support rollers. This was my first time changing out the motor. Surprisingly, the blowerfan blade came off the shaft of the motor very easy. I was concerned about the age of the dryer and was anticiapating this could be a problem fortunately, it came off very easy. Removing the old motor was easy. The only issue I had was seating the new motor in the correct position. I felt that the motor was not in the correct posiotion however, I was not sure being that this was my first install.
After trying several times, rotaing the motor back and forth (side to side) within the motor holding end brackets the motor fell into place and I was able to put on the end motor clamps on correctly. The drying is now working.

Viewed video on website, however did not match model but put me in the ball park for an overall view. Thank goodness I had the insight to order the pully with the belt. I believe the pully failed first causing the problem with the belt. Recommend replacing both any way while you have it apart.

. I had replaced the idler pulley a number of years ago so I assumed that the noise was now due to either the sliders at the front of the drum or bad rollers at the back.. I removed power by turning off the breaker that serviced the dryer. After removing the lower front panel via the two sheet metal screws at the bottom I then removed the door panel. The safety switch behind the door had to be removed by depressing the sides of the switch after disconnecting the two push on connectors. One will discover that reconnecting the smaller of the two contacts to the unused contact on the switch will allow one to run the dryer with the door off or open. This can be useful to test operation after the repair is complete before reassembling the door and lower panels. I then removed the large panel that secures the front of the drum. The drum is then removed after releasing tension on the drive belt. All rotating parts and sliders could then be checked. Upon disassembly I found that the rollers and sliders appeared ok and decided to replace the idler pulley as a last attempt to fix the problem. This is best done by removing the tension arm and tensioning spring. the pulley is then more easily removed from the arm using snap ring pliers. After replacing the pulley and thrust washer with new parts I reassembled everything. I found it helpful to pretension the arm using a zip tie wrap in that the belt can be more easily reinstalled on the drum and pulley. When the drum and belt is properly in place and belt threaded, one can reach in with a pair of cutters and snip the tie wrap to re tension the system. The dryer has been running normally again for a week after affecting this repair.

After checking out a video showing how to change the belt I decided to tackle the job. First I pried up the top, there are two plastic tabs in the front corners that hold the top down to the front panel. The top swings upward and will stay in position while you continue to work. Using a 3/8 socket, I removed 4 bolts that hold the front panel onto the frame. Be sure to unhitched the wiring to the door switch and those to the control panel and then the front will come out by lifting it off the tabs in the lower corners. Put the front panel aside and slide the drum forward and out of the dryer frame. Remove the old belt noting how it ms oriented around the tensioner and motor pulley. Now everything should be exposed and you should take the time and clean the inside if I were you. Our dryer was filled with lint and dust but after a good vacuuming and wiping down with a damp sponge, it looked like new again. Put the new belt around the drum noting where it had sat before. There is a grove in the drum but our belt did not go inside their but on the drum itself. Slide the drum back in place and from underneath put the belt on the pulley and under the tensioner. Replace the front panel, rehitch the wires and put the top down and your done. My wife helped clean the inside which took longer than replacing the belt. Total time about an hour or so cleaning time included.

This amana dryer didn't have the lower panel with screws. Instead, I removed the brackets in the back and found that the whole top would separate from the rest of the body (except for wiring, of course.) There seemed to be screws holding the top to the base in the front, but these are just guide posts. There are two spring clips in the front that you can pop loose with a putty knife.

Then there are two screws inside that fasten the front to the rest of the frame. Once I removed these, and the electrical connections to the door switch and the light bulb, the whole front came of just by tilting it forward and pulling the front panel up off of metal tabs on the base.

The rest of the repair went smoothly per other descriptions.

Removed the bottom panel. Removed door to dryer and disconnected the door switch. Removed the top of the dryer. Now I had access to the drum basket of the dryer. Removed the belt and took drum out. The idler was accessible and easy to replace. I replaced the other drum support rollers. These were a bit difficult when it came to removing the clamp pins holding the rollers. Once you get one the other is easy. Reassembly is relatively easy and quick. Dryer no longer squeals, runs nice. I felt really good.

Replaced pulley, arm, glide pads and belt. Followed the video and it was a breeze. Dryer is back to "Like new". And much cleaner inside!

There was initial rumbling and thumping then the drum failed to rotate under power. I could however rotate the drum by hand. This site suggested the rollers or belt as well as the idler assembly. I decided to renew all the wearable parts and ordered the belt, rollers, glides and idler assembly. It was in fact the idler. The idler wheel had disintegrated and collapsed in the center. It must have run (rumbling) until it finally seized and stopped. Replaced all the parts and the dryer is even better now than new. It was a good opportunity to vacuum out all the lint inside the cavity (that took most of the time and also found $0.36 in loose change). Also found it easier to remove the electrical connections with pliers rather than pull on the wires and risk detaching the wire from the clip.

I followed the online video on PartSelect website. No other instruction necessary.

I totally disassembled the Dryer, and replaced the Guide Rollers, Blower Wheel, Idler Pulley Shaft, Idler Pulley, and Belt.