NDE7800AYW Amana Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Marcia from Hammond, LA
- Parts Used:
- WP37001132
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Cylinder Seal came out
Early in the life of my dryer, the Cylinder Seal came out. For the past two years I put off buying the part. When it came in, I p[opped the top of the dryer, removed the two screws holding on the front panel, and pulled the Cylinder of the back wall of the dryer. I then placed the seal in the right spot, glued it down and reassembled. About Fifteen minutes of work and a cheap part, and now my dryer dries a l;oad of clothes in an hour instead of three.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from Petaluma, CA
- Parts Used:
- 37001141
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Vent filter was broken, and lots of lint was passing through to vent line
Removed the two nuts at the bottom of the dryer front to be able to move the front piece. Removed three screws holding the vent assembly in place. Removed vent assembly, replaced with new part and replaced screws and nuts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scot from Apopka, FL
- Parts Used:
- 37001070
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer would start when pushing start button
Removed the control panel disconnect the wires on the bad part and replaced with new. Extremely quick and easy less than 10 minutes. Part ordered on line and received within one day.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from hillsborough, NC
- Parts Used:
- WP37001132
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Worn Felt Seal
remove bottom two screws on lower front panel, remove panel. remove two screws on lower portion of door panel, pull bottom panel towards yourself to release pins at the top. Disconnect wiring for light and door switch (make sure to note what wires go where. Complete removal of front door panel. Remove 4 screws holding cylinder frame in place, lift to remove. remove remnants of old felt seal, use rotary tool to remove excess glue, etc. apply glue (used rubberized gorilla super glue), apply felt seal - allow glue to set up. reinstall in reverse direction from removal. Be sure to use glue as there are no clips or other retaining pieces for the new felt and it will not hold in place. overall pretty easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theodore from NEWNAN, GA
- Parts Used:
- 37001086
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Felt strip had come off existing lint filter screen
New filter screen does not have a felt strip. However, lint filters are important and my wife likes having a second filter. The new one fits very well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Ada, OK
- Parts Used:
- 56000, WP40111201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers
will not blow air
I first unpluged the dryer. Then I
Removed two screws and removed bottom cover, Then removed the door assembly.Here I had to unplug the light and door switches. I then removed the four screws that holds the tub mount in place, Then I removed the eight screws that hold the blower cover in place, then removed the blower. replaced blower and reassembled in reverse. I started the dryer and it worked fine.
Removed two screws and removed bottom cover, Then removed the door assembly.Here I had to unplug the light and door switches. I then removed the four screws that holds the tub mount in place, Then I removed the eight screws that hold the blower cover in place, then removed the blower. replaced blower and reassembled in reverse. I started the dryer and it worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Fort Worth, TX
- Parts Used:
- 33001640
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dryer would not heat sometimes while on Delicate temp setting.
1) Unplug dryer.
2) Remove the 3 screws to remove control panel from the main unit.
3) Remove the metal back to the control panel by removing 3 more screws.
4) Remove the knob from the temperature selector switch.
5) Pull the switch out, leaving the wires connected.
6) Unplug each of the 4 wires, one at a time. I plugged them directly into the new switch before going to the next wire, to ensure I didn't mix anything up.
7) Put everything back together in the opposite order.
The part was a perfect match and it is working great.
2) Remove the 3 screws to remove control panel from the main unit.
3) Remove the metal back to the control panel by removing 3 more screws.
4) Remove the knob from the temperature selector switch.
5) Pull the switch out, leaving the wires connected.
6) Unplug each of the 4 wires, one at a time. I plugged them directly into the new switch before going to the next wire, to ensure I didn't mix anything up.
7) Put everything back together in the opposite order.
The part was a perfect match and it is working great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from HOOPA, CA
- Parts Used:
- 56000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set, Wrench (Adjustable)
Dryer started making a terrible sound, when my son opened up the appliance he found that the Blower wheel was broken and the housing was full of debris.
My son will discribe how he did the repair.
First I opened the top, then I removed the front with a 1/4 inch ratchet and socket. I took the cover off the blower housing with a nut driver. Used the appropriate socket and a 1/2 inch ratchet, and an adjustable wrench to hold the motor shaft and removed the Blower wheel. I replaced the broken Blower Wheel and put all it back together.
Our dryer is now working great and there are no unwanted sounds emanating from within. We are very happy with PartSelects promptness and that we recieved the correct part as ordered. PartSelect website was easy to navigate. We plan if the need arises to do so again in the future.
Thankyou Frank and Rodney
First I opened the top, then I removed the front with a 1/4 inch ratchet and socket. I took the cover off the blower housing with a nut driver. Used the appropriate socket and a 1/2 inch ratchet, and an adjustable wrench to hold the motor shaft and removed the Blower wheel. I replaced the broken Blower Wheel and put all it back together.
Our dryer is now working great and there are no unwanted sounds emanating from within. We are very happy with PartSelects promptness and that we recieved the correct part as ordered. PartSelect website was easy to navigate. We plan if the need arises to do so again in the future.
Thankyou Frank and Rodney
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vicky from Browns Mills, NJ
- Parts Used:
- WP37001298, WP37001036
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
When the dryer was on it would still tumble, but made an aweful sound
My son n law took the fron off the dryer, whilw I looked on the inertnet to locate whatever part we would find to be in need of. He pulled the front panel off and the drum out to dicover it was the bracket and glide. They were easily replaced by popping the bracket out and snapping th new one in then placing the guide on it proper spot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Milton, FL
- Parts Used:
- WPY54414
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Loud Squealing Sound When Dryer Is Running>
First unplug the dryer,then remove the front bottom panel. With your 5/16 nut driver reach to the rear of the vent tube under the dryer and remove the lone screw that holds the tube in place. Lean the dryer forward and remove the tube from the rear of the dryer,this will allow you to see and reach the idler wheel from the front. Release the belt,feel for the clip that holds the wheel in place on the opposite side of the front,with your thumb nail or something else if preferred pry out on one side of the clip until it pops off. Slide the wheel off being careful not to lose the washer,slide the new wheel on and replace the clip. Put the belt back on replace the tube,which is actually the toughest part because you have to find the hole for the lone screw as you can't see it,but with a little patience it is easily enough done. Put the vent hose back on replace the front panel and plug it in and go!!it took me 30 min. Alittle tough to feel for some of the parts,but really much easier than you would think.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Puyallup, WA
- Parts Used:
- WPW10116735, WP503979
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Socket set
Dryer wouldnt heat up
Took the cover off the front of the dryer by removing the two screws that hold the cover in place. Then removed the two screws that held the heating element in place and removed the heating element. Removed the screws that held in the theremostats and then disconnected the two wires and put them on the new thermostat. Rescrewed them in with excisting screws and then put the heating element back in. Put the cover back on and turned on the dryer, and presto it all works again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GILBERT from SAN JOSE, CA
- Parts Used:
- 37001141
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Air duct was broken,taking too long to dry
removed the bottom panel. then the door. unscrewed the 4 screws, removed duct and replaced. parts came fast and fit just right! no issues at all! I recomend Parts select as an appliance vendor for parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mark from westland, MI
- Parts Used:
- 37001086
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken frame
Very easy to locate parts and discriptions with on-line service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOSEPH from ANSONIA, CT
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The female catch in door was bro9ken
I took out the old worn out part and replaced with the one I order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Priscilla from Portland, ME
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer door would not close
discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!
Was this instruction helpful to you?
Thank you for voting!