LE8267W2PLE8267W2 Amana Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Lincoln, NH
- Parts Used:
- 61927, WP40111201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
no heat and worn out belt
The repair went very well. The parts were a perfect fit and arrived earlier than expected.It took a little longer than it should have to do the repair because of my recent surgery I had my 11 year old grandson operating the nut driver taking the dryer apart install the parts then reassemble under my watch full eye. You could say it went so easy a fifth grader could do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Ellettsville, IN
- Parts Used:
- WP40113601, WP37001042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
had a annoying screeching noise when drying clothes
basically i took the whole front of dryer off and removed drum from there i could reach the rear rollers and changed them all is quiet now i also cleaned lint from blower motor and lint housing now it sounds like more air is moving and i beleive it dries clothes faster --runs and sounds brand new again!!
Thank's Partsselect
G.Booker
Thank's Partsselect
G.Booker
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stuart from Port Charlotte, FL
- Parts Used:
- WP37001132
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Dryer tumbler was rubbing on metal
As it turned out, the felt was only part of the problem. The guide bracket had been cut thru by the drum. This all started when a golf tee got stuck in the drum area. It took very little time to destroy the guide bracket. Dryer was built by Whirlpool. Parts are built to the bare minimum. These appliances are designed to break in a couple of years. There is no doubt about it. I installed the new guide brkt, glued the new felt on and put it all back together. The job is pretty straight forward but you need to be mechanically inclined.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wardell from Glenwood, IL
- Parts Used:
- WPY54414, WP56461, WP37001042
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
A squealling noise from the idler pulley.
Removed the bottom panel. Removed door to dryer and disconnected the door switch. Removed the top of the dryer. Now I had access to the drum basket of the dryer. Removed the belt and took drum out. The idler was accessible and easy to replace. I replaced the other drum support rollers. These were a bit difficult when it came to removing the clamp pins holding the rollers. Once you get one the other is easy. Reassembly is relatively easy and quick. Dryer no longer squeals, runs nice. I felt really good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JEROME from NILES, IL
- Parts Used:
- W10169313
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
switch clip broke
Unscrewed front panel. Pulled off unbroken wire connecter and popped switch and put new one in. Replaced front panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from POMPTON LAKES, NJ
- Parts Used:
- WPY54414
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Loud screeching from idler pulley
The round exhaust duct in the back my dryer can be removed simply by pulling straight out. This gives full access to the belt tension wheel. Slip belt off the wheel, remove snap ring with snap ring pliers, remove washer and wheel. Install new wheel, attach belt, and reinstall duct by looking right down the middle to line up properly. Dryer sounds like new again. 10 minute job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from SAGLE, ID
- Parts Used:
- WP40113801
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
No Heat
very easy after the learning curve. I ordered this thermal fuse on Friday morning and got it Monday by 11:00 am. I love this kind of service. I will use this company again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- bernadette from WINTHROP HBR, IL
- Parts Used:
- WP502140P
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed new lint filter
Just replaced old for new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pete from ANAHEIM, CA
- Parts Used:
- W10169313
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door switch was defected
The door switch was easy to replace. It is located in the right bottom of the door and I popped out with my fingers. Follow the wire connectors from the old switch and remounted back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JEAN from KINSTON, NC
- Parts Used:
- W10169313
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The dryer door would not cut the machine off when it was opened.
Installed the new part. Worked great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- maria from ROCHESTER, NY
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
dryer door would not stay closed.
I unscrewed the door catch and pried out with some resistance the strike part. Screwed in the catch and pushed in the strike. Closed door. Voila!! Back in business with assurance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Wimberley, TX
- Parts Used:
- W10169313
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door switch malfunction. Did not stop when door open.
Remove the front,2 screws. Replace switch. Only problem was holding front in position and starting screws at same time. Two person to finish.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Amarillo, TX
- Parts Used:
- W10169313
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken prong
I began by removing the two screws at the lower part of the front panel. After removing the panel I was able to access and remove the broken switch which was located on the front panel. I popped out the old switch and replaced it with the new one, reattached the wires and put the front panel on and the jod was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Apopka, FL
- Parts Used:
- WP40113801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Dryer stopped working but still had power.
After finding the culprit was the vent duct no longer connected to the internal drum duct, and cleaning the whole inside of the cabinet out. Must be a dryer made on friday or monday as no clip or screw to keep the two pieces together. Caused it to vent inside the unit. Pulled the bottom off, key is to remove the tension clips that hold the front panel on and then pull it off as there were additional tension clips holding it together. Unscrew the two screws with a nut driver that hold the thermal Fuse part. Change out one wire at a time to keep them aligned properly. Screw it back on, reattach bottom and start it up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from NEW ROCHELLE, NY
- Parts Used:
- W10169313
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Door switch broke
Just follow the video. The hardest part is getting the top to disengage from the clips.
Was this instruction helpful to you?
Thank you for voting!