ALG866SAC-PALG866SAC Amana Dryer - Instructions

Ordered the part, you made it so easy. Received it in two days, very fast, by regular mail. Perfect fit. Pulled out the old broken one and put in the new one!

My son will discribe how he did the repair.
First I opened the top, then I removed the front with a 1/4 inch ratchet and socket. I took the cover off the blower housing with a nut driver. Used the appropriate socket and a 1/2 inch ratchet, and an adjustable wrench to hold the motor shaft and removed the Blower wheel. I replaced the broken Blower Wheel and put all it back together.
Our dryer is now working great and there are no unwanted sounds emanating from within. We are very happy with PartSelects promptness and that we recieved the correct part as ordered. PartSelect website was easy to navigate. We plan if the need arises to do so again in the future.
Thankyou Frank and Rodney

First unplug the dryer,then remove the front bottom panel. With your 5/16 nut driver reach to the rear of the vent tube under the dryer and remove the lone screw that holds the tube in place. Lean the dryer forward and remove the tube from the rear of the dryer,this will allow you to see and reach the idler wheel from the front. Release the belt,feel for the clip that holds the wheel in place on the opposite side of the front,with your thumb nail or something else if preferred pry out on one side of the clip until it pops off. Slide the wheel off being careful not to lose the washer,slide the new wheel on and replace the clip. Put the belt back on replace the tube,which is actually the toughest part because you have to find the hole for the lone screw as you can't see it,but with a little patience it is easily enough done. Put the vent hose back on replace the front panel and plug it in and go!!it took me 30 min. Alittle tough to feel for some of the parts,but really much easier than you would think.

Removed two screws on lower front dryer panel with 5/16" socket and wrench. Removed three screws and plastic filter dryer screen vent with 1/4" socket allowing easy access to upper limit thermostat switch located on side of igniter flame assembly tunnel. Removed two screws attaching limit switch and disconnected two wires. Replaced with new limit switch and reconnected wires. Reassembled dryer. Works fine. Drying time for regular items such as towels is now less than 1 hour.

Unplug Dryer. Remove 2 5/16in hex screws fm lower panel,3 51/6in hex screws to vent duct. Remove 2 1/4in hex screws to thermostat. Remove 7 1/4in hex screws to blower cover and 2 5/16in hex screws holding base footings.Use adj. wrench to hold rear nut on motor shaft, use7/8in socket to remove fan frm motor shaft. Remove 3 5/16in hex screws holding fan housing to motor mount. Lift-up on spring tensioned belt pulley to remove belt. Pull motor & mount out [wires are layed toward front allowing removal]. Use 6in flat tip screwdriver to unsnap both front/rear motor clamps.Pinch plastic end clamps and remove motor electrical connector.Motor installation is reverse. For belt removal,remove 2 5/16in hex screws to door panel [unhook 2 wires to upper RT rear to door switch].Remove 4 5/16in hex screws to front bulkhead panel.Allow drum to sag IN PLACE [removal not required to replace belt],note belt location and slide old belt off and new one on
Replace Bulheald and door panel [re-attach door switch wires].Complete install by lifting belt pulley and feeding new belt into place. Hand rotate drum to ensure proper belt allignment and tracking. Replace lower panel. Vacuum interior as necessary. Parts delivered in 3days and fit perfectly.

I guessed that this was the part needed.............wrong! Changing it out was easy but the dryer does not work any better. I took the back off of the top of the dryer, unhooked the part, pulled the dial off the front and removed it. Put the new one in and put it all back together. No problem other than my guess! The part was great and I got it in an extremely timely manner.

Super easy. 2 screws allows you to remove the access panel. One screw on the igniter bracket removes the igniter. Pull off the 2 wire connectors and plug into the new one. Test the dryer and close the access panel.

I pretty much followed a lot of the earlier postings on partselect.com that provided encouragement to pursue replacing this part on my 17 year old dryer (sorry, money is tight these days and I prefer repair to $800 replacement).

I'd like to add that I borrowed a pair of snap-ring pliers from work which made removal and later securing of roller onto shaft much easier and probably avoided a lot of knuckle bruising and cursing.

I erred though in a couple of places during the replacement. Disassembly took about 20 minutes. However, when I re-assembled I had mistakenly already put the roller onto the shaft before trying to put the drum back in. That isn't possible so I had to remove (an initial groan but only a few extra minutes in the end) the roller from the shaft, then reposition the drum and then the roller back on the shaft.

I also decided to replace the belt while I was in there and I should have taken a picture or made a drawing of the belt route before I took it off since I was later left pondering how the heck to snake the belt onto the shaft and also the tensioner. A quick trip to the internet though showed me a similar route and reminded me how to route it.

I'd also like to add to be cognizant of the wires on the door and front panel when disassembling.

Anyone with any sense of mechanical ability and a little common sense ought to be able to do this repiar.

Thanks Part Select!

The repair looked simple enough until it came time to take the out wheel off. Because you can not hold the motor shaft(and the wheel screws on) it was necessary to remove the whole motor assembly and then grind the out shaft down, then use a small screwdriver to take the remaining shaft off.
I must say it was nice to recieve the part in as fast as I did we live in a very rural area and things like that are very hard to find

First of all I would not have done this if it wasn't for
your website. Using the schematics to figure out
the right parts was easy. It was also helpful in the
actual repair process. I have added your website
to my favorites in my browser. The parts arrived in 3 days and I live in Reno. Great Website.

M.B.

Being my lousy Maytag washer died THE PREVIOUS DAY, spewing water, etc. and I had rushed out and bought a new washer, I was determined not to replace the dryer (though I now am a serious NON_FAN of Maytag).

I disassembled the whole dryer and finally got to the blower wheel which was broken lose from the molded nut. I supposed something like a dime or penny got in there to shred it.

PartSelect's website allowed me to find the part in 5 minutes. It was on my doorstep the next afternoon.

Installation was straightforward BECAUSE I stacked all the screws and and labeled them appropriately. It took about 30 minutes to reassemble and the toughest bit was getting the drum in with the belt positioned properly.

Had to lay dryer on back. Cause it didn't have a back cover had to take the front door off and go in thru the front. Had to take the vent off. Had to use scotch tape to hold the belt in place while I got it on. It would have been a lot easier if they had a back cover. I only hope I don't have to do it again as it squells a bit on start up. Bill

First we had to virtually take the entire dryer housing apart - not very user friendly. We found that one of the two mounting screws on on of the rollers was gone. The mount was just wobbling around which caused the roller to fail and all of the noise. The wheel removal was a bit tough since there is very little room to pull it up and off of the center post. Definately need at least one helper to pull up on the drum while the wheels are removed and installed. Once the two new rollers were in place, the dryer worked like it was new. Not an easy job, but very do-albe - saved a ton of money doing it myself. Two must - haves: good set of snap ring plyers and one patient helper.

As it turned out, the felt was only part of the problem. The guide bracket had been cut thru by the drum. This all started when a golf tee got stuck in the drum area. It took very little time to destroy the guide bracket. Dryer was built by Whirlpool. Parts are built to the bare minimum. These appliances are designed to break in a couple of years. There is no doubt about it. I installed the new guide brkt, glued the new felt on and put it all back together. The job is pretty straight forward but you need to be mechanically inclined.

I first removed the front panel and door on the dryer using a 5/16th nut driver. I needed to disconnect the light and switch to remove the door. I raised the top lid of the dryer to expose the drum. I rmover the fan schroud and lint filter by removing 4 5/16 screws with the nut driver. I disconnected the belt from the idle tension pully and removed the drum. The drum support rollers were visible on the back frame of the dryer. I removed the bad roller using snap ring pliers. After cleaning the roller support shaft and lubricating the shaft with grease I replaced the drum support roller and secured it with the snap ring. I also replaced the dryer belt although it was still workiing. I reasembled the dryer after giving the inside a cleaning with the shop vac. The hardest part was getting the belt secured with the tension idle pulley. When assemblying the fan schroud make sure it is snug against the fan so it doesn't leak. Replace the top and front door and cover connecting the switch and light. If you get the switch wires correct the dryer will run with the door shut otherwise reverse the wires.