AYE2250AYW Admiral Dryer - Instructions

It took me a bit to figure out how to get the outer case to come apart (there are two spring-loaded latches under the front edge of the lid, had to insert a putty knife at just the right spot then lift up the lid). Once it was taken apart, I manually spun the drum to see where the noise was coming from and it was obviously coming from one of the two wheels that support the rear of the drum. Took out the drum after sliding the belt off and replacing the wheels was a piece of cake. They are held on by E-clip style retaining rings, which I destroyed when removing them with a pair of pliers. Luckily the new set comes with new retaining rings, along with the required washers and spacers. I also replaced the metal pins that the wheels spin on, since mine were showing wear and I wanted to make sure it wasn't going to keep squealing after I was done! All in all it was pretty easy! Before you take the belt off, make sure you take note of how the belt winds around the tension wheel so that you put it back on correctly! My girlfriend was VERY impressed that I was able to fix her dryer for about 1/10 of what it would have cost to get a new one!

Quick fix it works
remove the two screws holding the top from the back. Pull out the top section with the knobs
You should now be able to see the high limit fuse and the heating element.
Remove the two screws holding the fuse to the dryer. Replace the fuse and test before covering.
Also clean up the heating element with a soft brush or blower.

The support roller broke and that made the noise as the rubber came off the wheel. It took about 8 months before the belt finally broke. Since I had it apart I decided to change both the drum felt seals and idler pulley wheel. I had trouble finding high temperature adhesive for the drum felt seal. Lowe's and Home depot didn't have anything that indicated it would take the heat. Finally located an adhesive at a craft store and the label claimed it was good on washers and dryers. Although I was able to glue and stretch the felt onto the dryer by myself if you have two people it will be alot easier. My dryer had made so much noise for so long I couldn't believe how quiet it is now.

Unplugged electric, turned off gas valve. Opened top using a putty knife, laid it gently back against the wall for support. Removed 2 screws holding front on-leaned front out about 3-4 inches- while holding front with my knees I disconnected door switch wires.-then removed front panel. Followed instructions on maintenance sheet glued on underside of dryer top (Lucky it was there). Took tension off drive belt. Removed belt and drum following instructions on lid sheet. Removed old slides (worn out) Installed new pads & slides. Vacuumed out all lint/dust/dirt I could reach, Cheked rear drum rollers. Reinstalled everything that I had removed. It took extra time to do everything because dryer was in tight space, little working space. Turned gas on, plugged in electric cord. Worked great now.

First we had to make the blower wheel hole bigger with a file and a dremmel tool due to our dryer being a little older model with a slightly larger shaft. Works great now, we saved ourselves about $400. and we love doing that with today's economy.
Thanks PartSelect!!!

I received the part I ordered immediately and the included instructions made installation a snap. Thank you for your help. I would not hesitate to order from your company again.

Unplug dryer

Pick the top up at the front and swing up. Inside each side of the front is a screw to remove. Do not forget to unhook the door switch wires. Pull the drum. Push belt off as you remove the drum. Works better to reach in at the lower right and take the belt off of the tighener first.

After you clean out any lint in area unplug the wires from the motor and snap off the hold down clamp on the back bearing.

The blower needs to be released fromt he shaft. The snap ring in front of the blower needs to be taken off. This can be done with a screw driver by prying off the flat spot on the shaft. However, a snap ring pliers would be better. The front of the blower housing must come off as the blower must come off. There is a snap ring behind the blower that must come off also.

The biggest problem I had was removing the front motor bearing housing from the plastic blower housing. It is easy once you see that the front bearing housing is held in by four tabs in the plastic housing. By rotating the front bearing housing 90 degrees you will be able to pull it out.

From there just reverse your action. The belt went on ok. I found by putinng the belt on the drum and the motor drive pully first I was able to reach in an put the belt over the tighener.

Hinged open the top of the dryer. While dryer was running I tapped on the thermostat. The heater came back on. This verified the problem. Unplugged the thermostat, unscrewed it and replaced it.

I noticed my dryer was heating, but not tumbling. I"m a 53 year old single female, and my dryer I bought used 3 years ago. I had no clue what the problem was. I texted my brother and said, "it heats but doesn't tumble - is it shot?" He texted back "probably the drive belt - pop the top and see." So I popped the top, and sure enough, the belt was broken. So I googled "diy + dryer + drive belt" and watched a You Tube video. I then drove all over town looking for a belt, and the only place that carried it had closed at noon (saturday). So I googled " appliance parts + dryer and came to this site, ordered the part and it was delivered in two days.
I borrowed a nut driver from my brother, removed the front of the dryer, used a plastic cup to prop up the drum. I put the belt on the drum, being sure to place the ribbed side down, looped through the pulley and onto the motor, removed the cup, put the front back on, dropped the top, replaced the lint trap and the two screws holding that in place, turned the dryer on and voila! All done.

removed front cover, lifted drum up with a clamp and replaced slides. Replaced front cover

Real easy I have resurrected my dryer may times so this was easy to replace the belt and idler pulley

Step 1. UNPLUG DRYER
Step 2. Remove the selector knob(timer). It just slides off by pulling it toward you.
Step 3. Remove the back cover of the Control Panel. Three phillips screws along the top and three 1/4" hex head screws along the back. After removing the fasteners lift up on the panel and it can be removed.
Step 4. Remove the two 1/4 hex head screws that hold the timer to the control panel. (They are on the front of the control panel under the selector knob that was removed in step 2.)
Step 4. Switch over the wires one at a time from the old timer to the new timer. Don't forget to switch over the resistor.
**Note**Also pay attention to original position on the timer, it can be installed 180deg's out(upside down) then the knob will not be indexed poperly with the control panel.
Reverse the steps to reassemble!

I opened the top then i did change the heater element kit only one screw out and finaly replace the temperature switch, again one screw out was realy ease was my first time,the professional online help my, every one can do it thanks i appreciate your help.H.E.K.P/N AH2162280 - temp/switch p/n 31001449.

Pulled the broken blower wheel off the motor rod and replaced the new blower wheel on it. Need to make sure to place a small amount of grease to the motor rod. This will help slide the blower wheel on the motor rod easier.

my ex husband took the top and front of dryer off and removed the drum and belt. he pulled off the worn roller and replaced it with the new one. we put the drum in backwards and had to turn it around but all went well and the dryer is quiet again!!!