ADG20L1H Admiral Dryer - Instructions

Pry the front of the top up - it's held on with barbed fasteners that just snap out. Underneath the hood against the back panel is the heating coil assembly. On top of it is the thermostat, hanging from the side of it is the thermal fuse. I removed the heating elements (coiled wires held in frame) to make access to the other parts easier.
Pretty much plug-n-play. One nut driver takes off everything, you might need a needle-nosed pliers to push the lugs onto the contacts of the replacement parts (they fit VERY snugly).

Also, remove the front panel and clean out the lint in the air duct - lint collecting there is apparently what drives up the temp causing the fuse to blow in the first place.

First I opened the top of the dryer, then removed the bracket holding the high limit thermostat. Then I removed the heating element to gain access to the thermal fuse. Installation was the reverse. I also cleaned out the lint trap on the front of the dryer and also checked the vent duct (it is cleaned every year). Very easy repair.

I watched a video. The man speaking was Wayne from parts direct. He made the repair go so smoothly. I enjoyed watching him and I hope you include him in more videos. Had dryer apart and back together (after I had to take top back off, to re-attach the door switch, which I forgot. Had a senior moment!!) in 15 min.And working as good as new. Thank you Wayne. Have a nice day. Bryan

Installed new coil, helped but have other issues that I'm troubleshooting.

replace two heating coils. Dryer working find.

All the videos said the same thing. If the Igniter works and the gas ignites bit shuts off soon after that, then the coils are bad. I bought the coils and it didn't fix the problem. My bad, I should have put my meter on it to test it before I bought the part and waited a week to get the coils. Now I'm in the process of illuminating the sensors. I will figure it out. Make sure you use the meter. It will save you the headaches.

I watched video provided on appliance repair. I followed the steps and exchanged out old parts for new and now my dryer works like a new dryer. thank you appliance repair for fast shipping.

I removed two wires from the coil valves. Then I removed two screws from the bracket that holds the coil valves in place. I removed the faulty coil valves and replaced them with the new ones. Put the bracket back on and replaced the two screws and wires. It took almost 5 minutes. The dryer is like new once again.

I used a socket to take of the front cover. I used a screwdriver to remove the two screws that held the coils in place. Replaced the coils and put everything backs together. Piece of cake!

removed the two screws that hold the coils in place pulled the coils terminal connections off removed and replaced with new coils reattached quick disconnect terminals dryer now works better than when it was new

Popped top open, matched up parts, changed them. Dryer cranked up,got hug from wife. Done life is good.

First i unplugged the dryer from the outlet. Then I used a flat head screwdriver to lift open the top cover of the dryer. I removed the two wires connected to the thermal fuse and removed the two screws that attached the fuse to the holder. I placed the new fuse on the holder using the two screws. I plugged the two wires back up to the fuse and closed the lid. Be sure to fixed what caused the problem before attempting to use the dryer. I my case there was a massive amount of lint beneath the lint tray which had the vent blocked.

After searching you site for other similar problems, we ordered the part that we thought we needed, it arrived within 3 days, my husband installed the part and the dryer started. The information you have on your site was great, it gives you an idea about what to test before having to call a repairman. There were several people that had the same problem and with their description it was easy to test the fuse. Thanks it saved us alot of money and time. I can't describe how the repair was done, my husband did it, but it was very easy

I tilted the unit back enough to scew the new legs into the threaded holes.

Unplug unit turn off gas, remove only bottom front panel first tried radient flame sensor was not the problem it was the coils which were infront easy to acess with small screw driver remove two prong coil and replaced then the three pronged coil being sure to line them back before tigtening left off cover and watched for ignition once it turned on and ran replaced cover and done.