Models > ADE25K3H > Instructions

ADE25K3H Admiral Dryer - Instructions

Jump to:

All Instructions for the ADE25K3H
121 - 135 of 473
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
bruce from east waterbrough, ME
Parts Used:
341241
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Broken Multi Rib Belt-92-1/4''
I took the back of my dryer off to see if the problem was there. I saw that the belt was broken and laying on the inside of the dryer. Took belt and went on line (Google) my KitchenAid Dryer from it's model number. The website was PartSelect. Found the belt I needed and saw a video on how to replace the belt. I called to order the belt and spoke to Steve, which help me with all my needs. Steve knew just the belt I was looking for and placed my order. The belt arrived a few days later. While I was waiting for the belt to come in, I removed the front of the dryer and get ready for reinstall. It took me about 15 minutes to install the belt and put the front of the dryer back together. I found PartSelect to be very helpful and saved me, maybe $150.00 by not having to call a serviceman to do the easy replacement. Thank you Steve and PartSelect, now I'm number 1 with the wife again.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Linda from BURSON, CA
Parts Used:
WPA3167501
Difficulty Level:
A Bit Difficult
Total Repair Time:
Less than 15 mins
Light bulb went out in mictowave
Screwed the new “$40” dollar light bulb back into the recessed socket. The new bulb is much smaller that the original bulb and much harder to get fingers into small area where the bulb went. After several try’s, I got it in.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jeffrey from South Amboy, NJ
Parts Used:
341241
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Worn Out Drive Belt
Pull dryer out from wall about 6 to 8 inches step 1 - romove front/bottom access panel. Step 2 - remove lint trap and remove 2 screws (philips type) that is under lint trap door. Step 3 - push in 2 wood shime in front edge between lid and front panel (angled shims like door shims - a putty knife will work to, just be carful not to scratch finish) step 4 - fold lid upward and back (like on a hinge) step 5 - looking from where the bottom/front acces panel was losten 2 screws - one left one right about 3 turns - 9you can remove them it just makes it easier to reinstall the front panel. Step 6 - find appropriate pot or stacked 2 x 4 pieces - something to hold up the drum when you remove th front cover, and from underneeth support the drum. Step 7 - look thru bottm front access hole - there are 2 springs that come down from the door - and clip onto the frame of the fryer - unclip them and place on the side. Step 8 - remove 2 upper screws that hold front panel on, and remove front panel, if you left the bottom screws attached but loosened you have to lift up on the front panel a bit. Step 9 - looking from the bottom thru where access panel was - you will see motor on right with a additional roller (tensioner) - push upwards on tensioner to relieve pressure on motor and pop off belt (remember where tensioner is and how it clips in to base. Step 10 - work belt off of drum towars front - to remove it all the way you will have to lift up the drum slightly off of the pot or whatever you used for support so the belt can clear. Stem 11 - new belt goes on the same way you took to old one off - plat side away from drum with ribs against drum. Step 12 - again lift up on drum and work belt back on. Step 13 - tricky part is how to get the belt back on the motor - prentend you are threading a needle wht a folded over piece of thread - hold the belt with about a 4" loop with your left hand - hold up on tensioner and feed it back thru and work belt back over end of motor pulley, after front panel is back on with the 4 screws tightened spin the drum and make sure belt is between the 2 lines marked on the drum and remove the pot or whatever u used to prop up the drum. Dont forget to attach the springs for the door assemble all other components in reverse order. And dont forget to take the pot back out
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Monique from Roosevelt, NY
Parts Used:
341241
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench set
dryer turned on but did not tumble
I removed the lint trap then the dryer cover from top and front side. I placed the belt around the dryer drum being sure to put it on the correct side with the grid side against drum. I coiled the belt around the pulley and motor tract. Replaced everything in opposite order in which it was removed.
Video from website was very informative and helpful. I was able to follow along step-by-step to replace the dryer drum belt. I am officially a do-it-your-selfer!!!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
terry from allenton, WI
Parts Used:
341241
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Screw drivers
broken drive belt
Remove back panel, looking for access. upon reassembly dropped socket into lint trap. Dissemble again, also dissemble lint trap ducting, found it almost completely blocked by lint, clean and reassemble. Remove front panel and there is the problem of the broken belt. Try to look up online to no avail because I didn't have the proper machine ID, but I did find out where to look. Now with the right info ordered the part. Received in the post about 5 days. Upon reassembly I realized that the adjustor was laying in the bottom, picked up, cleaned inspected, OK, then needed to figure out where it goes, got it, then to figure out how it holds tension on belt. That took a few minutes, well maybe 10 then the old Ford light bulb came on, then installed the belt and adjuster. Replace front panel, slide back into place, hook up wiring and duct. Test, guess what folks it works.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
robert from sanford, NC
Parts Used:
530106
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Wrench set
noise
the same way it was described on your site, this dryer is nearly 17 years old, I've needed to change this at least 5 times.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bob from Chesapeake, VA
Parts Used:
341241
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Broken Drum Belt
Lift top of dryer. Remove two 1/4" screws that hold the front panel. Disconnect the two wires on the door switch. Lift front panel to remove. Lift drum enough to install the new belt. Reach in to place the belt on the motor and tension pulley. Replace the front panel. check for free rotation of the drum and belt. Close top. Done.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Saint Petersburg, FL
Parts Used:
WP53-1107
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
Gas dryer not drying clothes in one cycle
Unplugged the dryer. Released the two forward sping clips holding the top in place and hinged it open. Removed the two 1/4" screws(one on each upper edge of front panel). Disconnected the door switch. Pulled out and up to remove the front panel. Located the cycling thermostat on the blower housing. Disconnected the thermostat wires, removed the (2) 1/4" screws. Installed the new thermostat and assembled in reverse order.
4 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Deidre from Brownsville, TX
Parts Used:
WPA3167501
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Microwave oven bulb had burned out
My Dearest One removed the screws that held the part that covers the bulb; removed the old bulb, put in the new bulb and replaced the cover.
The whole operation took less than 5 mins.
Thank you.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Steve from Fort Atkinson, WI
Parts Used:
341241
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
broken belt
First I had to find my way into unit . I took out screws that didn't have to come out, but eventually I found my way in. I took out the drum put the belt over it and through the tightener then over the motor pulley. I then put the sheet metal back on and the job was done.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
craig from Mckinleyville, CA
Parts Used:
530106
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
loud clunking noise while running dryer, then noise went away and not much air blowing out
first pryed up the dryer top, pulled the two wires for the door switch and removed front panel. remove 8 or 10 blower housing cover 1/4" screws. removed blower moter shaft snap ring pulled out damaged blower wheel. slid on the new wheel with the flats on the shaft and new wheel alighned up. installed blower clamp around blower stub. installed motor shaft snap ring. reinstalled blower cover cover. installed front dryer cover to include installing door switch wiring. put down top and pushed dryer back into place making sure to install the blower vent hose. started dryer to test operation. all worked well the first time.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Powhatan, VA
Parts Used:
341241
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Broken belt
Disassembled dryer to gain access. Cleaned out dryer and installed new belt. Reassembled dryer and checked function.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Pawan Kumar from Quincy, FL
Parts Used:
341241
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Dryer drm belt was worn out and needed to be replaced
First of all let me begin by telling you that this was my first D-I-Y project. The dryer had been out for over a month and the clothesline drying of clothes, while being energy efficient, did not go well because it was the summer/fall borderline and the ants and bugs were inside the clothes which were brought into the house.

I googled my problem and soon enough there were a ton of helpful sites available offering solutions to my problem. So, after I decided to do it myself, I ordered a new belt from part-select. Once the belt arrived, I went back to for help. There was an extremely useful video among the results. The whole thing took me about 20 minutes as I was doing it all by myself. I followed the steps and was able to replace the dryer belt very easily and I am so very thankful to have a working dryer again before the onset of rain and cold!
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Craig from Pepperell, MA
Parts Used:
341241
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Tumbler belt broke
When the dryer drum stopped tumbling, I followed the instructions on PartsSelect to remove pop the top of the dryer and then remove the screws to remove the front panel. Then I could see the broken belt underneath the drum.

I did pull out the drum itself to get a better look at the motor and pulley to see where the new belt would need to go. I replaced the drum by pushing it back and then rotating it so it would fit back into the groove on the rear panel.

Once I received the new belt, I followed the steps included with the belt package to loop the new belt around the drum and then thread it over the pulley and around the motor.

The entire repair was very easy and so much cheaper than buying a new dryer.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Carlos from Mount Holly, NJ
Parts Used:
341241
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
dryer drum wouldn't turn because of broken belt.
First I removed the back panel (and found out later when I received the belt from Partselect.com, that this was unnecessary). I followed the instructions that came with the belt and removed the top panel and then the front panel. I placed a piece of wood under the drum for support so that it would not be just hanging from the back. Then I found the broken belt lying on the bottom, and a pulley that was unhinged. I replaced the pulley following the instructions, and vacuumed the motor and all around. I put the new belt around the drum and then through the pulley and onto the motor axle. I replaced all the panels and the dryer is now working like new.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the ADE25K3H
121 - 135 of 473