ADE25K3H Admiral Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Steve from WASHINGTON, IA
- Parts Used:
- 341241
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Worn out belt
Was a little hard getting at the idler pulley being it was behind the blower assembly, but it was the only draw back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from NEW CREEK, WV
- Parts Used:
- 341241
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Broken Dryer Belt
First thing was to disconnect power to the dryer. I lifted the top lid and found 1 screw on each side at the top near the front and removed them. I also removed the door switch (CLIPPED ON) leaving the wires connected to the actual switch. Then the front panel lifts up and outward. I was able to install the belt from the front, guiding it back to the pulley/idler arm. Reassembled and it worked great. The belt I bought from this site appears to be better than original stock. It should last a long time. :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from UTICA, NY
- Parts Used:
- 341241
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
My dryer heated but would not tumble, the belt was the problem, it broke. UNPLUG APPLIANCE
I watched an online video about how to replace a dryer belt & followed the directions. Placing the belt around the drum is easy but stringing it thru the pulley is a little difficult because the belt has tension. This takes a little effort but is doable. Dryer runs great now........Be sure to unplug appliance 1st........
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Leaf River, IL
- Parts Used:
- 341241
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Socket set
Clothes dryer drum would not rotate
Disconnect the power and gas supply so that you can slide dryer out and into an accessable area to work comfortablely. Removed top and front of dryer. When disconnecting numerous wires from the top controls, draw a simple color coded diagram for reconnection before you disconnect those wires. After removing the top and front, take out the drum and clean all the lint, money etc. out of the normally nonexcessable area of dryer. Place new belt on as you replace the drum. This takes two people; one to hold the drum in position and one to carefully work the new belt into place. Rotating the drum by hand will assist in the placement of the new belt on the drum. After reassembling the newly cleaned dryer it was a pleasure to try it and find a dryer that worked better than during its pre-repair use and it saved us the price of a repair call or a new dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jenny from Lisle, IL
- Parts Used:
- 341241
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
dryer is heating but the drum is not moving
first, i read all the comments on this web site as well as other web site. sooner i confirm the problem is the drum belt, i order the parts.
my kemore model front panel is one piece. so i have to lay down the dryer and open the front panel on the top. The instruction sheet sent with the belt is very good, so it does not take too much time to replace the belt, the challenge task is to reconnect the front panel to the side panel. I spend too much time trying different way to use the fastner hook to connect panels without realizing that the hook is broken. stupid me. i later have to use the wire to connect the front panel to side panel. overall, i am very happy i fix the dryer.
my kemore model front panel is one piece. so i have to lay down the dryer and open the front panel on the top. The instruction sheet sent with the belt is very good, so it does not take too much time to replace the belt, the challenge task is to reconnect the front panel to the side panel. I spend too much time trying different way to use the fastner hook to connect panels without realizing that the hook is broken. stupid me. i later have to use the wire to connect the front panel to side panel. overall, i am very happy i fix the dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Cincinnati, OH
- Parts Used:
- 341241
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver
The drive belt broke in half.
With no experience repairing appliances, I did figure it out that the drive belt was broken since the motor was running and the drum did not turn.
What to do? Start looking for fasteners! I knew I had to get to the drum, but there was nothing up front, on top, or bottom that gave a clue. Only the back panel had hex head steel screws. I removed them and the panel. Then I removed a tube that pulled air from the drum to the outlet. I saw some screws holding the back of the dryer top. After removing them, the top popped off by pulling it up and releasing the attachment at the front.
This gave me access to a couple of screws holding the top of the front (holding the door). It seemed to make sense to lay what was left of the dryer on it's back. After removing the last two screws at the top corners of the front panel, I pulled it up and removed it. The drum lifted right out. The belt tightener was loose and lying against the back wall.
The local Sears did not have a replacement belt and their web site was not that helpful or forgiving. A Google search revealed a site called PartSelect. It had a very useful search routine which led me to make a purchase on a Saturday evening. The belt arrived at my door on the following Tuesday! Be sure to look at the instructions that come with the belt, it will demonstrate how to fish it through the loose belt tightener.
In about 1.5 hours the dryer was back together and doing it's thing. There were two additional screws left over, but I figure that's a manufacturing defect.
I was a hero to the wife, as usual.
What to do? Start looking for fasteners! I knew I had to get to the drum, but there was nothing up front, on top, or bottom that gave a clue. Only the back panel had hex head steel screws. I removed them and the panel. Then I removed a tube that pulled air from the drum to the outlet. I saw some screws holding the back of the dryer top. After removing them, the top popped off by pulling it up and releasing the attachment at the front.
This gave me access to a couple of screws holding the top of the front (holding the door). It seemed to make sense to lay what was left of the dryer on it's back. After removing the last two screws at the top corners of the front panel, I pulled it up and removed it. The drum lifted right out. The belt tightener was loose and lying against the back wall.
The local Sears did not have a replacement belt and their web site was not that helpful or forgiving. A Google search revealed a site called PartSelect. It had a very useful search routine which led me to make a purchase on a Saturday evening. The belt arrived at my door on the following Tuesday! Be sure to look at the instructions that come with the belt, it will demonstrate how to fish it through the loose belt tightener.
In about 1.5 hours the dryer was back together and doing it's thing. There were two additional screws left over, but I figure that's a manufacturing defect.
I was a hero to the wife, as usual.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- oliver from moss beach, CA
- Parts Used:
- LA-1008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
noise and vibration getting louder over an extended period of time
The repair was much easier than anticipated. Next time I could do it in less than 30 minuites.
Replaced the axel that holds the rollers as well as the rollers. Just rotate the left one 90 degrees and it slides out.
Probably what took the most time was puting the belt back on. It is old so I was being careful. It took a couple of trys to keep it on the rollers as I moved the drum into position. So easy I am convinced to buy another Maytag.
Wife was impressed so that's worth something!
Replaced the axel that holds the rollers as well as the rollers. Just rotate the left one 90 degrees and it slides out.
Probably what took the most time was puting the belt back on. It is old so I was being careful. It took a couple of trys to keep it on the rollers as I moved the drum into position. So easy I am convinced to buy another Maytag.
Wife was impressed so that's worth something!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruben from Basprop, TX
- Parts Used:
- 341241
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Drum would not turn, but machine had power.
Before ordering the part, I found this website by linking from a video on YouTube where several people showed how they did it. Simply two screws in the lint removel chute and pushed in the two clips holding the top and two inside screws holding the front panel. Held the machine tilted back onto a table and placed two 4" wooden cubes underneath it so it wouldn't come forward and one more 4" cube under the drum. After cleaning out the inside, I slipped the new belt around the drum (ribbed side down) and taped it in place with a couple of pieces of painter's tape temporarily. Hooked the idler wheel guide and looped the belt in it. Tested movement by spinning it by hand to check alignment and removed tape. Reassembled the front, side and top panels accordingly and tested it. Voila! This was my first attempt and I saved myself some bucks. The last repair was done by Se•rs and their service person took my credit card number for the invoice and promptly went out and charged over $3,000 on it. He was eventually caught. Great incentive to do yourself, huh?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erika from Swarthmore, PA
- Parts Used:
- 341241
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Dryer drum wouldn't turn
First, I unplugged the dryer. I pulled up the lint filter, then unscrewed the two screws there. Then pulled up the top panel. I had a helper hold it up since it couldn't lean against the wall. Then I had to take the front panel off the dryer. The idiots at Kenmore used screws, not pins, so I needed to use a socket wrench to get those two out of the top corners. Then I lifted it up and off. I removed the broken belt. I put in the new one. I replaced the pulley, which had fallen without the tension of the belt holding it in place. It was pretty easy to figure out how it went, but I consulted the online community for a diagram. I threaded the belt in place, replaced the panels, and viola! It worked. Easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robbi from PowderSprings, GA
- Parts Used:
- 341241
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
The dryer would not tumble
I watch the video and played it again while I was working.
I am a 54 year young woman and I did it.
I am a 54 year young woman and I did it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from Yorkville, IL
- Parts Used:
- 341241
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The belt broke.
Ordered belt, received it two days later. It was a perfect fit.
The top of my dryer pops up from the front where 2 screws will allow the front to drop to the ground. Lift the drum slightly to get the belt on. Had to wrestle with the idler arm for about five minutes, but I won.
The top of my dryer pops up from the front where 2 screws will allow the front to drop to the ground. Lift the drum slightly to get the belt on. Had to wrestle with the idler arm for about five minutes, but I won.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernard from Hadley, NY
- Parts Used:
- 341241
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Belt was old & slipping.
- Unplug the electric dryer.
- Manually opened the top of the dryer.
- Unclipped the wire assembly attached to the front panel of the dryer.
- Removed two screws holding the front panel of the dryer, and remove front panel for access.
- Very Important!! Note how the old dryer is currently installed before proceeding.
- Rotated the dryer drum while working the dryer belt toward the rear of the dryer.
- Removed the dryer drum.
- Removed the old dryer belt.
- Put the new dryer belt around the dryer drum and put the dryer drum back onto the drum rollers and into the rear guides.
- Here's the hard part, lay on floor and reach into the pulley area and motor - wrap new dryer belt around these belt rollers as "noted" in the fifth step.
- Rotate dryer drum by hand to ensure the new dryer belt is exactly installed as the old dryer belt.
- Reinstall front panel.
- Reclip wire assembly onto the front panel.
- Manually close the top of the dryer.
- Plug in the electric dryer.
- Manually opened the top of the dryer.
- Unclipped the wire assembly attached to the front panel of the dryer.
- Removed two screws holding the front panel of the dryer, and remove front panel for access.
- Very Important!! Note how the old dryer is currently installed before proceeding.
- Rotated the dryer drum while working the dryer belt toward the rear of the dryer.
- Removed the dryer drum.
- Removed the old dryer belt.
- Put the new dryer belt around the dryer drum and put the dryer drum back onto the drum rollers and into the rear guides.
- Here's the hard part, lay on floor and reach into the pulley area and motor - wrap new dryer belt around these belt rollers as "noted" in the fifth step.
- Rotate dryer drum by hand to ensure the new dryer belt is exactly installed as the old dryer belt.
- Reinstall front panel.
- Reclip wire assembly onto the front panel.
- Manually close the top of the dryer.
- Plug in the electric dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from Farmingdale, NY
- Parts Used:
- 341241
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
dryer would not spin
Step 1. Read all the comments about how to do this job in this forum. (i found them very useful)
Step 2. Read the directions that come with the dryer (they helped a lot)
Step 3. Don't forget to disconnect the power cord before reattaching the door switch wires (oucH! ) or doing anything with your dryer.
Step 2. Read the directions that come with the dryer (they helped a lot)
Step 3. Don't forget to disconnect the power cord before reattaching the door switch wires (oucH! ) or doing anything with your dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Mobile, AL
- Parts Used:
- 341241
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The belt that turns the drum broke.
Removed the two screws holding in the Filter and removed the filter.
Removed the two screws holding the front onto the dryer.
Put the belt over the drum and proped the drum up.
Reseated the tension spring and pully in the proper slot. (On my machine it is the position closest to the motor).
Reassembled the dryer in the reverse order.
Removed the two screws holding the front onto the dryer.
Put the belt over the drum and proped the drum up.
Reseated the tension spring and pully in the proper slot. (On my machine it is the position closest to the motor).
Reassembled the dryer in the reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from Springfield, MA
- Parts Used:
- 341241
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
dryer drum wont spin
-Took top of by prying with screwdriver.
-2 screws and door wire to take off front panel.
-proped drum with 4X4 piece of wood.
-looped belt around drum where the mark for the old belt was.
-looped belt through tensioner and pulled with the screwdriver over the motors drive shaft.
-manually spun drum to make sure everything was right.
-put panels back on and was done.
You cant go wrong with the included directions and belt diagram. this is the first repair I've done of any kind that went flawless.
-2 screws and door wire to take off front panel.
-proped drum with 4X4 piece of wood.
-looped belt around drum where the mark for the old belt was.
-looped belt through tensioner and pulled with the screwdriver over the motors drive shaft.
-manually spun drum to make sure everything was right.
-put panels back on and was done.
You cant go wrong with the included directions and belt diagram. this is the first repair I've done of any kind that went flawless.
Was this instruction helpful to you?
Thank you for voting!