DE20F5HW Admiral Dryer - Instructions

first, i read all the comments on this web site as well as other web site. sooner i confirm the problem is the drum belt, i order the parts.
my kemore model front panel is one piece. so i have to lay down the dryer and open the front panel on the top. The instruction sheet sent with the belt is very good, so it does not take too much time to replace the belt, the challenge task is to reconnect the front panel to the side panel. I spend too much time trying different way to use the fastner hook to connect panels without realizing that the hook is broken. stupid me. i later have to use the wire to connect the front panel to side panel. overall, i am very happy i fix the dryer.

With no experience repairing appliances, I did figure it out that the drive belt was broken since the motor was running and the drum did not turn.

What to do? Start looking for fasteners! I knew I had to get to the drum, but there was nothing up front, on top, or bottom that gave a clue. Only the back panel had hex head steel screws. I removed them and the panel. Then I removed a tube that pulled air from the drum to the outlet. I saw some screws holding the back of the dryer top. After removing them, the top popped off by pulling it up and releasing the attachment at the front.

This gave me access to a couple of screws holding the top of the front (holding the door). It seemed to make sense to lay what was left of the dryer on it's back. After removing the last two screws at the top corners of the front panel, I pulled it up and removed it. The drum lifted right out. The belt tightener was loose and lying against the back wall.

The local Sears did not have a replacement belt and their web site was not that helpful or forgiving. A Google search revealed a site called PartSelect. It had a very useful search routine which led me to make a purchase on a Saturday evening. The belt arrived at my door on the following Tuesday! Be sure to look at the instructions that come with the belt, it will demonstrate how to fish it through the loose belt tightener.

In about 1.5 hours the dryer was back together and doing it's thing. There were two additional screws left over, but I figure that's a manufacturing defect.

I was a hero to the wife, as usual.

I googled 'replace dryer belt' and found instructions on the 'Virtual Repair Man' web site. After reading the instructions through twice I began.

First I removed lent filter and removed the two screws that hold the lent body in place. I rotated the top panel up and back and leaned it on the wall; proped up the dryer drum with some scrap wood pieces; rotated the front panel of the machine out enough to slip the new belt, groves down, around the drum; reinstalled the idler pulley under the drum; raised the drum slightly and reattached the front panel. Reattached the top panel and replaced the filter. Did a test run and worked good.

I got a price from Sears for the part and they were asking $45 just for the belt. I saved enough in parts and labor to take my wife out for a real nice dinner. thanks

Remove back panel, looking for access. upon reassembly dropped socket into lint trap. Dissemble again, also dissemble lint trap ducting, found it almost completely blocked by lint, clean and reassemble. Remove front panel and there is the problem of the broken belt. Try to look up online to no avail because I didn't have the proper machine ID, but I did find out where to look. Now with the right info ordered the part. Received in the post about 5 days. Upon reassembly I realized that the adjustor was laying in the bottom, picked up, cleaned inspected, OK, then needed to figure out where it goes, got it, then to figure out how it holds tension on belt. That took a few minutes, well maybe 10 then the old Ford light bulb came on, then installed the belt and adjuster. Replace front panel, slide back into place, hook up wiring and duct. Test, guess what folks it works.

Disconnect the power and gas supply so that you can slide dryer out and into an accessable area to work comfortablely. Removed top and front of dryer. When disconnecting numerous wires from the top controls, draw a simple color coded diagram for reconnection before you disconnect those wires. After removing the top and front, take out the drum and clean all the lint, money etc. out of the normally nonexcessable area of dryer. Place new belt on as you replace the drum. This takes two people; one to hold the drum in position and one to carefully work the new belt into place. Rotating the drum by hand will assist in the placement of the new belt on the drum. After reassembling the newly cleaned dryer it was a pleasure to try it and find a dryer that worked better than during its pre-repair use and it saved us the price of a repair call or a new dryer.

First thing was to disconnect power to the dryer. I lifted the top lid and found 1 screw on each side at the top near the front and removed them. I also removed the door switch (CLIPPED ON) leaving the wires connected to the actual switch. Then the front panel lifts up and outward. I was able to install the belt from the front, guiding it back to the pulley/idler arm. Reassembled and it worked great. The belt I bought from this site appears to be better than original stock. It should last a long time. :)

I watched an online video about how to replace a dryer belt & followed the directions. Placing the belt around the drum is easy but stringing it thru the pulley is a little difficult because the belt has tension. This takes a little effort but is doable. Dryer runs great now........Be sure to unplug appliance 1st........

Pretty much just followed the video - I'd never opened a dryer before, so I'd watch a step, pause and do it, then run the video a few more minutes, and repeat. These dryers are really extremely simple devices: just a heater, then a motor to spin the drum and run the fan (I think the same motor does both). So you loosen a couple of screws, pry the metal case open, and slip on the new belt. Done! I didn't keep track of time, but I'm psyched to have saved myself a $200 repair call! Standard delivery arrived in less than two days, just like they said it would.

Followed the instructions and the repair went like clockwork, took less than an hour. I spent more time brushing and vacuuming old lint from the innards of the machine than I did doing the actual repair. Finished up $0.78 richer, too, from the change I found inside the machine.

Was a little hard getting at the idler pulley being it was behind the blower assembly, but it was the only draw back.

Shut off power and gas, unscrewed lint vent, raised top on angle with rope, unscrewed and moved door switch, unscrewed and took off front, put new belt around drum, then raised front end of drum with 4 narrow pieces of 1" foam insulation which let me view and install the belt connection to the drive motor shaft, adjusted the level of the drum using the rope holding up the top, removed foam pieces, replaced and rescrewed the front to fit the drum front channel, replaced the door switch, replaced the top and screwed it to the lint vent, returned gas and power, and ran confirmation test.

Belt was broken Removed the front (very easy) removed the drum. Noticed the roller was damaged. Replaced the roller. Installing the belt was tricky but followed an on line video. This dryer has the motor and tensioner behind the blower housing. There was not enough room to use both hands effectively. So first I placed the belt on the motor then pulled the tensioner until I could slide the belt on the tensioner with my other hand. This was the reverse order from the video. The dryer now seems to be quieter.

I watched the video on replacing the belt and it was amazingly as easy as the video described. I had asked my son if he could replace it if I couldn't and I didn't have to ask him. If you are only moderately ept at repairing anything you could do this. I was waiting on it when it finally arrived and in no time I had it replaced and my dryer back working. Being a woman I like it when I can repair something myself and not have to rely on someone else to do it.

The repair was pretty simple.
1. unplug dryer.
2. use a med. flat screw driver with some cloth wrapped around the blade as not to chip the paint surface. From the front of the dryer,
carefully pry open the top surface of the dryer. There are 2 points to lift, about 3" from the right side and 3" from the left side.
3. The top will open like the the hood of a car, lift gently, you might have to move the dryer out if you can (if you are on a flexible service connection).
4. Unclip the push bottom elec. switch.
5. Carefully remove 2 sheet metal screws on the top left and top right (from the inside of the dryer cabinet. These hold the front of the dryer in place. You have to remove the front of the dryer to get the drum out. I can't believe that these 2 flimsy screws hold the dryer together.
6. Pull the front panel off, tipping it forward. More on this later, it's really important!!
7. Remove the drum, it's light weight, but bulky.
8. Now you will see the motor assembly and idle pulley.
9. Follow the belt diagram with the replacement belt package.
10. It gets a little tricky to get the drum back in because there's a bit of spring tension on the drum from the belt.
11. You're ready to re assemble. BUT, the next step is really important.
12. Since you have the front panel off, you can get at the lint trap. Yeah, lint. Ever wonder why your favorite Tee shirt gets thinner and thinner? Well, look in the lint trap. I filled a vacum cleaner bag with the hard packed lint.
13. By the way, you have to remove the 2 torx screws that hold the lint trap assembly.
14. Vacuum the whole exhaust pipe while u are at it.
That's it!

Unplugged the 220 line, removed lint cover, (2 screws). Lifted top with a screw driver, (2 plastic fasteners) then unplugged a ground line at the front lip to separate the front panel. There was a 50/50 chance here that I would not put the wires back correctly, didn't not make note of the color differences. There was no lower panel, just a single panel on the front, which I first tried to remove like the top, but quickly saw no results, then lifted the panel easily, which I set aside. I rested the drum on a 4x4 piece of wood. I then slipped the new belt over the drum, aligned the bulkhead at the rear, and positioned the belt in the original position, there was a distinct mark showing this. Next I saw the idler pulley lying on it's side, hmm, thought this might take some time, but the illustrated instructions were very accurate, reset the pulley, pushed it toward the motor and doubled the belt around the pulley, it sort of felt right, according to the grooves on the floor panel. I then rotated the drum counter clockwise, then tested. It worked! Became a hero to my wife and found $1.86 in change, woo hoo! Total cost, including shipping under $20., two day delivery, amazing. Thanks.