AED4516MW0 Admiral Dryer - Instructions

Good

I noticed my dryer was heating, but not tumbling. I"m a 53 year old single female, and my dryer I bought used 3 years ago. I had no clue what the problem was. I texted my brother and said, "it heats but doesn't tumble - is it shot?" He texted back "probably the drive belt - pop the top and see." So I popped the top, and sure enough, the belt was broken. So I googled "diy + dryer + drive belt" and watched a You Tube video. I then drove all over town looking for a belt, and the only place that carried it had closed at noon (saturday). So I googled " appliance parts + dryer and came to this site, ordered the part and it was delivered in two days.
I borrowed a nut driver from my brother, removed the front of the dryer, used a plastic cup to prop up the drum. I put the belt on the drum, being sure to place the ribbed side down, looped through the pulley and onto the motor, removed the cup, put the front back on, dropped the top, replaced the lint trap and the two screws holding that in place, turned the dryer on and voila! All done.

I received the part I ordered immediately and the included instructions made installation a snap. Thank you for your help. I would not hesitate to order from your company again.

Used the maintenance kit....followed the movie tutorial. I also used an empty gallon plastic container to support the front of the drum while stretching the belt over the motor pulley. For the rear drum rollers, before sliding them on the shaft, I put a light grease film on the shaft. After the repair, the dryer runs quieter.

Unplugged unit and removed top and front of dryer. Removed drum and belt. noting how belt ran through the belt tension-er. Removed old felt seal from rear of drum. Replaced broken baffle, replaced rear seal. reinstalled belt. Put unit back together and test ran.

The replacement parts are truly easy to exchange. Everything is located behind the rear panel. A few fasteners needed to be undone. What's really important is another video that explained what should be "checked" when a dryer malfunctions. VERY IMPORTANT viewing. I spent an afternoon going over the front inside and rear of my dryer. I'll probably get another ten years from my dryer thanks to this site data and videos.

1. Unplug unit, next disconnect vent then remove back cover. 2. replaced element (very easy) then 2 thermostats, then put cover back on. 3. Removed frt. cover by following directions that came with maint. kit this too was easy. The hardest part is getting belt on as your putting drum back in, and even that was only so hard. Just TAKE YOUR TIME, and you will get it.

Asking my question on you tube they show me problems and parts to need replace and how do installation.

My son took the timer hood off with a Phillips, head screwdriver and replace the Timer. Then he put. Tim hood back on the dryer.

To replace the thermostat and heating element, I followed the video from PartSelect.

Before buying the parts, I had already taken my machine apart to clean it and check for lint build up, but there was only a bit of dust, no major blockages. Because the burning smell was metallic, I just had my fingers crossed that replacing the heating element and thermostat would do the trick. It worked!
There is an odd ceramic sort of smell in the first 5 minutes of using the new element but that went away and all is working well at this point.

My components looked slightly different from those on the video; I had fewer wires so I just took photos of everything before I started to make sure I put it all back in the correct place.
I had to watch another video on how to easily remove the thermostat, mine was stuck. I just used a flat head screw driver behind it like a lever and gently pried it off.
It took me about 30 minutes total only because I had to watch a couple of extra YouTube videos due to the differences of my machine. I don’t usually do repairs like this one and wanted to be completely sure I was doing it correctly, but the work/repair itself was super easy.

The lint trap seal was just because mine got damaged when I took it apart to clean it. I just pulled the old one off, made sure the old adhesive was completely removed, (it peeled off like scotch tape), I cleaned it, then I slowly went around the edge of the vent/housing and stuck the new foam seal down. No video required, just common sense.

My dryer started squeaking and I thought it was the drum rollers, so I bought a set. When I attempted the repair and got as far as removing the dryer drum and I decided to spin the shaft on the motor and that was where the squealing was coming from. I put the rollers on and reassembled the dryer. One day later the motor seized up. Ordered a new motor and installed it with no problems. The nut on the back of the motor ended up being a 20mm wrench. Motor cost me $105.56 and the maintenance kit (ps37308) (2 rollers,4 clips, button clip, new idler pulley and belt) cost $32.08. It cost a total of $137.64 in repairs with no labor costs and I accomplished it in under an hour. Minor handyman skills needed or find a friend who is handy. My dryer is 14 years old and now is running like new again. I used the 50% rule, if a repair exceeds 50% of the cost of a new machine, replace it, if the repair can be done for less than 50% of the cost of a new on, fix it.

i took the face off dryer and removed the belt and drum then removed the lint trap from back to clean and have access fan then removed the retaing clips holding the motor then with two adjustable wenches unscewed the motor from fan took out motor and replaced in reverse order all you needed was some common sence to do this i though it was easy to do greats parts fit perfect thanks tommy

I am a teacher and teaching is my game. I have always, with my four children, taught them to do mechanical work themselves. I and most of my children have a PhD, but in having said that, I confess, we come from a very mechanically talented family. It shows and proves to be of great benefit.
OK, so much for the intro.

I gave my daughter the tools and said, "What do you think is wrong with the dryer and where would you start?" She tested it and said, "The motor is running, but the tub is not turning thus I conclude it is the belt because I can hear the motor running eliminating that as a cause.

She then opened the top, looked around and removed two screws from the lint catcher. She looked it over, looked a me, I shrugged my shoulders and she then took a rubber hammer and popped the top off. Don't ask me how she knew that, but I think she saw the rubber pins through the crack between the case and top. She raised the top after removing two screws in back to relieve the simple hinge and also disconnected the wiring clip and sure enough, the broken belt was inside the cabinet. We called you, the best, fastest and most accurate service on the Internet and ordered a replacement. I would like to add, the price is always more than fair and delivery very prompt.

When the part came, my daughter took it up to our laundry room and within twenty minutes, she tested it and everything was fine. She did smell a little burning smell which might be attributed to a new belt or the fact that there was no clothing in the dryer.
Thank you so very much.
Dr Robert E McGinnis

removed old gasket took door off 4 screws. cleaned seal area applied glue put on gasket easy

Dryer ran with no heat. Replaced the Thermal Fuse and when that didn't fix the problem discovered the element was burned. Easy fix except the F-disconnect fitting broke when I tried to remove it and male fitting on the heating element is 0.375 and all I could find were 0.250 F-disconnect fittings. I finally found a supplier who had a 0.375 fitting and the repair took 10 minutes after that. The online videos at PartSelect are excellent.