ADE20L4H Admiral Dryer - Instructions

Had a problem holding drum in place and putting front back on. Got it together and drum wouldn't turn. Had to tear it a part again and belt had turned.

After reading everyone else's comments I started by pulling out the dryer, unplugging the power and exhaust. Next moved the dryer to an area where I had room to lay it on the back. Then using a flat blade screw driver, I popped the top attached tape to the top so I could lean back the top without having to hold it. Removed the two screws from the front panel and removed the door safety shut off before removed the front panel. Then I layed the dryer on its back. Then reached under the drum, pushed the belt tensioner toward the motor puller to release the tension on the belt. Then slid the belt to the base. Pulled the drum up and out of the cabinet. Next I cleaned all the lint and crud out of the dryer components. To remove the clips that hold the rollers in place, I use 2 small flat blade screw drivers. These are inserted at the back side of the horse show shaped clip between the shaft and the clip. When the two screw drivers are rotated like turning a screw they slide the clip out. Next I used a socket wrench with a #8 metric socket(I didn't have the sae size) and removed the screws holding the drum roller brackets. I simply reversed the procedure to install the new rollers. Since the dryer was on its back, when I put the drum back in, its own weight slipped it in place. Then pulled the belt around the drum and between the motor pulley and the belt tensioner. Holding the belt with one hand, I used the other hand to pushed the belt tensioner in and positioned the belt. Then I stood the unit back upright and put the front cover on, replaced the door safety switch, removing the tape holding the lid and then cloed the lid. Of course I put the dryer back in place, leveled it, and it now runs like brand new. My thanks to every one else who gave me hints that saved be about $450!

I took apart the dryer by unscrewing the top and the front, front comes off by just undoing the two top screws on the inside. I figured it was something to do with the rollers since the noise was ciclycal. The hardest part was to put the drive belt back on. It helps to have a second person for about 5 minutes.

Released lid clips, two screws removed to remove the front. Took tension off of the belt by removing it from roller, then lifting tension spring from base. Removed drum to gain full access to motor. Lubricated rollers, vacuumed all areas to remove lint. Replaced motor and belt. Re-installed drum and re-attached tension spring, dryer face, and top. Works fantastic. Hard part was getting spring released and reattached due to location.

Checked the voltage to the high limit switch. Found that the element was bad. Ordered the part from partselect.com. and received the part in two days. Unplugged the unit, pulled the lid on the dryer, used the 5/16" nutdriver, removed 3 or 4 screws, pulled out the old and installed the new. Saved a $100.00 service call from the repair man! Novice in home improvement can do this. Thank you Partselect!!!

Once I realized it was just a drum belt and how easy it was to fix, I ordered the belt myself with no help from a national warehouse hardware chain where the manager said "I don't have a belt but I can sell you a dryer." Thank you I kept my 300+ dollars and once I got the belt it only required removing the two screws that sealed the lint screen cannel to the top; popping the top, removing the to nutbolts fastening the front to the side panels; slidding the front panel out; putting the belt around the drum and attaching it properly to the tension pully and motor. Finally, I closed it up and tested it. Household hero in less than 12 minutes! Not bad for a psychologist, eh?

First unplug the machine and turn off the gas. Then, I pried the top up (2 clamps on front, 2 screws to the lint screen). Then I removed 2 5/16 nuts that fastened front panel to sides. I held the drum and pried the front panel back while my wife slipped the new belt around the drum. Then, I buttoned everything back up in reverse order, removed the kick panel, threaded the belt through the tensioner pulley and around the motor shaft. It's really that easy. PartSelect.com makes it simple with quick, accurate service.

first I took the two screws that hold the filter in, then disconected the power,then I poped the top of dryer up and removed the two 5/16 screws on the inside of the front panel then the two screws down by the loading door hinges and took off the front cover and the drum, replaced the belt and put the ajuster back on and put everything back in revers order and it is working like new thank you for the fast order .tony

Disconnect power. Removed front panel and lifted top. Removed belt around spring pully and motor assembly. Carefully eased belt around back of drum and gasket. Reverse process.

Took two screws out of the Lint tray on top. remove to bolts from under hood then put new belt on. Always make sure there are no twists in belt when put back on

I tilted the unit back enough to scew the new legs into the threaded holes.

Needed a belt. Only snag was for me was re-installing front panel (door)

Before ordering the part, I found this website by linking from a video on YouTube where several people showed how they did it. Simply two screws in the lint removel chute and pushed in the two clips holding the top and two inside screws holding the front panel. Held the machine tilted back onto a table and placed two 4" wooden cubes underneath it so it wouldn't come forward and one more 4" cube under the drum. After cleaning out the inside, I slipped the new belt around the drum (ribbed side down) and taped it in place with a couple of pieces of painter's tape temporarily. Hooked the idler wheel guide and looped the belt in it. Tested movement by spinning it by hand to check alignment and removed tape. Reassembled the front, side and top panels accordingly and tested it. Voila! This was my first attempt and I saved myself some bucks. The last repair was done by Se•rs and their service person took my credit card number for the invoice and promptly went out and charged over $3,000 on it. He was eventually caught. Great incentive to do yourself, huh?

Buy the part the site provide a video on how to do it and was very helpful thanks

Raise the top and then remove two screws to remove front. Once the front was removed on this Maytag model it was not necessary to remove the dryer drum. I simply lifted the drum slightly and slid the belt around the drum to position the belt. I then pressed the tension arm toward the drum and fed the belt around the drive pulley and tension pulley. I spun the drum a few turns by hand to insure that the belt was aligned properly. Then replaced the front cover and the top. Turned on the dryer to test and job was completed. Thanks to your video and prompt parts delivery the job was a snap. My wife didn't even have time to get mad.