ADE20K3CKDA Admiral Dryer - Instructions

I watched the video on replacing the belt and it was amazingly as easy as the video described. I had asked my son if he could replace it if I couldn't and I didn't have to ask him. If you are only moderately ept at repairing anything you could do this. I was waiting on it when it finally arrived and in no time I had it replaced and my dryer back working. Being a woman I like it when I can repair something myself and not have to rely on someone else to do it.

Belt was broken Removed the front (very easy) removed the drum. Noticed the roller was damaged. Replaced the roller. Installing the belt was tricky but followed an on line video. This dryer has the motor and tensioner behind the blower housing. There was not enough room to use both hands effectively. So first I placed the belt on the motor then pulled the tensioner until I could slide the belt on the tensioner with my other hand. This was the reverse order from the video. The dryer now seems to be quieter.

followed video except for the second fuse deeper down it was easier to take a piece of string and loop it around the top of the holder so it would not rotate toward the bottom due to the size of the hole for the fuse. hold string loop until bottom of bracket is in place and press top into place as you remove looped string...

First thing was to disconnect power to the dryer. I lifted the top lid and found 1 screw on each side at the top near the front and removed them. I also removed the door switch (CLIPPED ON) leaving the wires connected to the actual switch. Then the front panel lifts up and outward. I was able to install the belt from the front, guiding it back to the pulley/idler arm. Reassembled and it worked great. The belt I bought from this site appears to be better than original stock. It should last a long time. :)

Opening the dryer to discover the problem was easy. We put the belt up on a workmate bench - I think this made access better at the bottom. Getting the new belt on past the rear drum seal was ok, the instructions could benefit by including wording describing how to roll the belt flat under the 2 rear drum support pulleys to bring it to the drive motor shaft pulley. The instructions included with the belt had a diagram showing the position of the belt take up idler (the idler was found loose inside the bottom of the dryer), our dryer had a hole in the metal spring clip of the idler arm, so we thought at first that a screw to the chassis had broken - this is not the case the idler pulley is held in place by belt tension, so pulling the spring clip open while feeding the belt would have been useful in the instructions too. Other than those 2 head scratchers the repair was easy and saved us the cost of calling a repairman. Thanks PartSelect.

lift top of dryer unscrew the top of the pull out filter from the top of dryer. then unscrew the screws near top on the inside of the front panel and have an old soap container handy to hold up the dryer drum. lift the front panel up for removal and put the old soap container under the drum to keep it from falling out. Then mess around with the idler pulley and look up information under pictures of idler pulley in place with belt in Google to see how the belt fits through it.. Finally replace belt, check front and back of drum to insure proper fit and put the dryer back together to see if all works well. and see if the reason for belt breaking is apparant and more than just old age and use.

After reading some tips on the parts select site I isolated the high limit fuse and thermostat as the likely problem. The overheating was caused by a buildup of lint in the exhaust fan area. after clearing the obstruction, and replacing the fuse and switch I tested the dryer which worked perfectly.

First, I printed one of these responses which were excellent and very detailed. The screws connecting the lint slot to the top of the dryer was frozen. Taking the front panel off was difficult because I did not read the instructions I printed out very well. After I took the top off I had a hard time finding the 2 screws located inside on the top of the front panel. They are located to the far right and left at the top. To take off the front panel you have to push it up to release the clips on the bottom, then it comes right off. Taking the drum out was easy. What was difficult was putting the belt on. There wasn't any slack and to put it around the pulley and the drum for me was difficult. After that is was a piece of cake. It works great.

Unplugged dryer.
Popped the lid using a butter knife by pushing in the two latches (located about 4 inches in from the side in the seam where the top lid and front panel meet).
Used pliers to remove the electrical leads to the two fuses (two leads each fuse).
Unscrewed the top fuse from the mounting bracket, then removed the heating coil, then unscrewed the lower/bottom fuse from its mounting bracket. Tested each fuse with my trusty (and rarely used) volt/ohm meter -- which verified that I had bad fuses.
Replaced the bottom/lower fuse, re-attached to the mounting bracket, reconnected the electrical leads.
Replaced the heating coil.
Replaced the top fuse in its mounting bracket and reconnected the electrical leads.
Closed the lid. Plugged in the dryer. Works like a charm.
NOTE: I checked more than 50 feet of exhaust duct to make certain there were no clogs (which is what caused the problem). I discovered that my conduit (that tube-like thing that connects the exhaust from the dryer to the exhaust port in the wall or floor) was kinked and created a clog. I trimmed it and now it works and I have improved drying performance.

i pop the top of the dryer lose and removed the 2 screws that held the front on and installed the new belt and put it back to gethere

Dont go in through the back!! Take the top off then the obvious steps to get to the drum and belt. On the kitchen aid model at least I would advise to make all the hassel of replacing the belt well worth your time to go ahead and buy a new tension pulley with the wheel on it as opposed to the all metal tension pulley. My dryer is much more quiet now and seems to be more efficient.

I waited a two days to get my belt then deciced to get a new tension pulley. Ordered it one day and the next it was at my door. This was well worth my time and effort. Thanks PartSelect!!

Pry up front of top and lay back. Remove two 1/4" srews at top corners. The front of dryer will then swing to the right. The drumb will lift out easily. Remove broken belt. Inspect the drum rollers on the back wall. Replace if loose or not turning. Mine needed replacement. The assembly part is not easy. You need the drum in place and after it is in place you can't get the belt on. After 8 tries I got smart and made a prop to hold the idler pully up, then put the belt in place and let the pully down slowly. It worked! Put the front back on and the 2 screws and pop the top back down. Also it is a good idea to unplug the electric cord and turn off the gas (if app).

Worked with a guy, I'm a girl. He had a good "feeling" about how to take apart the dryer, install the belt and put it back together. After one go putting the belt on, starting the dryer and having the belt come off....I followed along silently looking at the directions. Definately needed 4 hands to put the drum back in alignment. Other than that, this was very simple PROVIDED THE DIRECTIONS TO REALIGN THE DRUM are followed at the end. So simply: my directions are meaningless here, just follow the ones enclosed with the belt and this should take no more than 1 hour. :)

Took the top off then front off of the dryer with just 2 screws( thank god not the back) and replaced the belt...had a difficult time getting the tension pully in place, belt kept falling off..the stop screw for the tension pulley was bent ,so had to replace that first.

Followed instructions for testing, starting with door switch, then push to start switch, then thermal fuse. Thermal fuse was bad. Replaced thermal fuse. Back in business.