DP8700XYN3 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Stanley R from Pineola, NC
- Parts Used:
- WPW10273574, WPW10509257
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Water intake hose leaked between plastic/hose connection (metal crimped clamp)
Since I had never made a repair on this 14 year old Kitchen Aid dishwasher, it was "discover as you go." First turned it on its back, took off bottom, disconnected both hoses and found out that hoses would not move. So, had to take off top and remove the back/side unit to get to hoses on top side where they were fastened by tape and a hose holder. Replaced hoses, used old clamp and "buttoned" it up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from Pomona Park, FL
- Parts Used:
- WPW10204131
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
my wheels to the top rack broke.
when my package arived , I open the box and pop on my wheels, and all fixed in 60 sec. Thanks you saved me about 650.00 for a new Dishwasher. Thanks Melissa
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from Schenectady, NY
- Parts Used:
- W10311986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old rack rusting
This is the second time I have replaced a rack. You just pop on the new rollers and you're good to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Milford, NH
- Parts Used:
- W10851031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
clips had broken on the support Support Arm
I used a pair of needle nose pliers to remove the
Upper Wash Arm Support Clip from the broken support arm. Very quick re-assemble with the new part and I was able to re-use the support clip. The upper wash sprayer unit with its new support arm easily clipped in place on the upper rack.
Upper Wash Arm Support Clip from the broken support arm. Very quick re-assemble with the new part and I was able to re-use the support clip. The upper wash sprayer unit with its new support arm easily clipped in place on the upper rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Boscawen, NH
- Parts Used:
- W11027965
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken silverware basket plastic silver ware fell thru
just thru old basket away put new one in very happy thank you will buy parts again thru u people again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from harrison, AR
- Parts Used:
- 3367910
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken gasket
Just put it on by hand, works great now, saved me at least 50.00!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luann from Springfield, MO
- Parts Used:
- WP3369769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Front panel of dishwasher was dented
Pulled off the bottom trim, slid the old panel off and put the new panel on. Then popped back on the bottom trim.
Was this instruction helpful to you?
Thank you for voting!
Foreign Objects Jammed Impeller
Disasembled pump to find dammaged parts replaced with new parts . Made wife very happy .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Murfreesboro, TN
- Parts Used:
- WP8268829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The upper spray arm was cracked where it mounted to the top rack.
Ordered a new upper spray arm from PartSelect. Shipping was fast and the correct part was recieved.
Use a hair drier to warm the prongs that mount to the upper basket. The plastic is softer and will squeeze/fit in place without snapping off the "ears".
Use a hair drier to warm the prongs that mount to the upper basket. The plastic is softer and will squeeze/fit in place without snapping off the "ears".
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Thomaston, GA
- Parts Used:
- WP3368999
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
detergent dispenser would not operate
remove star screws holding inside door panel. remove plastic cover that protects latch assembly. hook one end of spring on stationary pin on inside of slider bar. Hook other end of spring on pin on slider bar. replace cover and door panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Madison Township, PA
- Parts Used:
- 675806
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
dirty dishes
Installed pump kit. Was surprised the kit seemed different( some parts changed or deleted. Instructed to discard old parts and follow with new configuration. Reassembled and tried t fin it works fine now. Thank you so much
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Peru, IN
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
leaking suds and water front bottom of door
Replaced door gasget took 5 minutes tops. Ran cycle and still had leak. Called local repair person. After thoroughly checking out the dishwasher and running soapless cycle determined problem to be soap build up over time. He ran a commercial cleaner through a complete pots and pan cycle. No more suds and no more leak repair complete. Did not actually need door gagset but it was super easy to change and delivery service was great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Royal Oak, MI
- Parts Used:
- W10311986
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
worn and rusted lower dishrack
First, I checked the ripped box for damage to the dishrack. Fortunately, there was none. Then I looked for the instruction booklet. Unfortunately, there was none. And the parts bag was ripped and I did not know what was supposed to be in it. So, I rechecked the photo of the dishrack on the website and found that either parts were missing or the dishrack was different than illistrated. After a few moments of thought, I realized the latter was the case. I then figured I would have to use some deep thought to do the installation since neither the missing instruction booklet nor the unzoomable photo would help. So, I pulled out the tall thin thingamabob from the old dishrack and put it in the new one though it did not secure as tightly. Then I put the wheel units on just like the old one. What I could not immediately figure out was where the collapsible rack row was mounted. I eventually realized that the rod went into a hole in the wheel units and the latch mounted above one unit. I still have no idea where the two other tan clips go. Though the dishrack is different and thus requires different science to fill it, it appears to do the job.
Thanks for asking.
By the way, it was not blue.
Thanks for asking.
By the way, it was not blue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Schofield, WI
- Parts Used:
- W10311986
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The bottom dishrack was having areas that were breaking off and showing rust.
We took the rollers off the old one (new ones came with the dishrack also) and put them on the dishrack (they snapped on). There was also an extra piece that we figured out how to put on. Then slid it in place and it was fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from CHARLOTTESVLE, VA
- Parts Used:
- 675238
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
standing water in tub , not draining
removed old check valve from bottom of dishwasher and replaced with new one. I used channel locks to do this, disconnect hoses and screw out check valve, and put back in opposite order, make sure the dishwasher is empty of water or have a plastic bowl or such to catch water. Take off two front covers on bottom of dishwasher to access check valve ,white with hose attached.
Was this instruction helpful to you?
Thank you for voting!