DU830CWDB5 Whirlpool Dishwasher - Instructions

Came home and my husband had it all done. He said it was simple and it looks bran new again. Very satisfied.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

I ordered from you the address cleaner for my Kitchen Aid Dishwasher. I was hesitant about ordering it because, in my experience, these tyo e products are a waste of money and never perform to a level of expectation! But the washer is new and nice and I want to take care of it so in ordered the cleaner. I popped the little pellet in where the detergent pods go. Vli send the door pressed "normal wash" button, shut the door and forgot about it. I forgot about it until I opened the door to put in dishes, ... And BOY!! The inside of the washer was shining so bright I had to put on my sun glasses!! It would have been difficult to not notice how clean the inside of my machine was! No kidding... I was really impressed... in faction glad I got this request for feedback... because I was wondering how to let you j now what a great product this stuff is!

Opened the door by using a star screwdriver. Pulled the door inside from the outside. Located the broken spring, put in new one (be very carefull to see how the insides are put together..makes life ALOT easier), and carefully put back together.

Disconnected power. Shut off water supply. Took off the front, disconnected copper supply line and flexible water line, removed water inlet valve. Took elbow from old inlet valve and put in on new one. Put new valve in, reconnected water lines, put back front panel. Opened water supply, Flipped breaker back on. Done and it worked!

The repair was very simple. Simply pull the dishwasher out far enough to access the springs, remove the old with pliers and install the new springs in the same spot as the old ones.

we followed your instructions submitted via e-mail and they worked out just fine....thank you

I removed the top dishrack by removing the front clips(stops) on the tracks. Then I removed both tracks by removing the back stops. Then I replaced 7 wheels. Then I replaced the tracks, dishrack and the front stops. The whole job took about 20 minutes.

I watched the video, read all the post, they all said change the heater. So I did. Only there is a little fuse at the back of the unit that also goes bad and that was my issue. Have it ordered and will be going soon. That said, Part Select made finding and getting my parts a breeze!

Removed and installed new door gasket which I found to be a simple task. Ran dishwasher and it still leaked. I then looked at other repairs submitted by your customers with the same problem. One had mentioned removing the lower spray arm and checking the screws around the pump. Sure enough, 2 screws were nearly ready to fall out and all others were loose. Tightened those, reinstalled spray arm, ran the dishwasher and no leaks. A big "Thanks" to you and also to other customers for sharing both their problem and how they were able to fix it. It sure saved me some money!!

I just followed the video, and it now works perfectly! Thanks SOOO much! great site, great info.

Shut off water supplyand removed front cover below door. Remove flexable water line (wrench set), valve and bracket (nutdriver), and input hose (pliers). Installed flexable line on valve, replaced input hose on valve, then installed valve and bracket. Found screen on input to valve almost completely blocked with buildup of materail. Replaced front cover. result, bright, clean dished.

Performed repair as to Video shown in receipt after purchase of spring plus we used a friend who has same dishwasher and has performed the same repair recently, video was easier to follow though. All you do is push off lid with a screwdriver and pop off as per instructions on video then unlatch spring from ledge and pull off post, then just reinsert new spring in reverse order or follow video instructions either way is easy and takes about 15-20 minutes to install

The top of the latch was broken on I had to push the plunger back through the mounting to get it out. ai had to pull the whole assembly apart to get the locking nut out. i remove the latch assy and took about 10 minutes to figure out how to put it back together. Changing it with the help of the video wasn't hard but confusing at times. Thanks for the video.

Bought a house and with it can an old whirlpool dishwasher in where the soap dispenser lid would latch, as the latch itself was gone. Ordered the latch from part select and used the installation video to switch the latch out. Only problem I came across was that the torx screws at top of he door were free spinning. Ended up using a flat head for leverage to finally get the screws out. Everything works perfectly for once.