WDT710PAHB0 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- DOUG from KENTS STORE, VA
- Parts Used:
- W10311986
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lower dishwasher rack was deteriorating (extensive rust) and needed to be replaced
The lower dish rack rolls directly out of the dishwasher without problem - there is no permanent attachment. The new rack comes as a kit, which includes the 4 required dish rack wheels (Part # 6 in the diagram). One part (only) from the original dish rack needs to be removed and re-installed on the new rack - the upper spray arm tower (Part #5 in the diagram). That is easily removed from the original rack with a 1/8 counterclockwise turn, to disengage the 'feet', and installed on the new rack with a 1/8 clockwise turn. The kit is designed to allow for use on multiple models, so there are 'extra' parts left over, after it is used for the DU8500XX-2 dishwasher. These can be discarded.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeffrey from HOUSTON, TX
- Parts Used:
- WPW10491331
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Poor to no cleaning lower basket
lower wash arm cracked by spinning into items hanging out of bottom of basket. part twists and snaps right in. glue did not fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edna from WEST MONROE, LA
- Parts Used:
- WPW10653840
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
When cycling through it would stop up to 3 times & have to be restarted.
Replaced door latch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from PEMBROKE PNES, FL
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Top rail stop clip broke
Very easy to remove the broken one and just clip in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from BLOOMINGTON, IN
- Parts Used:
- W10537869
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Leaking dishwasher
Turned the dishwasher in its side. Used the video step by step. This is why we purchased from this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marie from Hollywood, FL
- Parts Used:
- W10518394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
water not heating,dishes not drying
My husband did this. He turned the dishwasher upside-down, disconnected the wires,and unbolted the heater.He put in the new heater (bolted,wired) and tested the current. Voila!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from SACRAMENTO, KY
- Parts Used:
- W11084121
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
would not shut off.
easy the sensor was on the right side, and easy to get to, I turn off the power, turned off the water, and pulled it out, the first thing I saw was the yellow wires and plug. took about 5 minutes, to replace it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Des Moines, IA
- Parts Used:
- 8269144A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Dish washer was very smelly.
After replacing garbage disposal. I referred to you video you sent me when i received the new replacement hose. That made it look very easy to install. Thank you for all your help and support.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Springhill, FL
- Parts Used:
- W10518394
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
element not working
laid dishwasher on its side and unscrewed element. returned unit upright & replaced element. reversed process and reinstalled unit under cabinet
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eladio from LOGAN, OH
- Parts Used:
- WPW10538166
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Develeoped a leak on the bottom.
Pulled dishwasher out of compartment, removed all parts underneath. removed inner parts, removed pump assembly. Installed new pump assembly and grommet. Reassembled in reverse order, test ran and unit was operating normal and no leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Warren from Campbell, CA
- Parts Used:
- WPW10337934
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench set
Broken door spring causing door to drop when opening or if not latched.
Unplug (disconnect power)
Shut off water
Disconnect water supply line
Clean up any water spills
Remove clips holding air gap hose and wire inside cabinet.
Open dishwasher door and remove two screws that secure dishwasher to cabinet (these are at top of door opening).
With door closed, remove panel under door (this has a screw clamp on each side that requires a quarter turn to release).
Lower the dishwasher as necessary to provide vertical clearance by adjusting leveling legs.
Pull dishwasher out from under counter (grip from under door) far enough to expose springs (one on each side). Take care to feed all connecting lines smoothly through cabinet opening.
Note how existing springs are installed.
Install new spring in the same fashion as the old spring was installed.
Test the door operation.
Push unit back under counter taking care to draw connecting lines back through cabinet opening.
Readjust leveling legs as needed.
Reattach unit to counter top.
Reattach water supply and open valve.
Check for water leaks both at valve and under unit, fix as necessary.
Replace panel under door.
Replace any clips inside cabinet.
Reconnect power
Shut off water
Disconnect water supply line
Clean up any water spills
Remove clips holding air gap hose and wire inside cabinet.
Open dishwasher door and remove two screws that secure dishwasher to cabinet (these are at top of door opening).
With door closed, remove panel under door (this has a screw clamp on each side that requires a quarter turn to release).
Lower the dishwasher as necessary to provide vertical clearance by adjusting leveling legs.
Pull dishwasher out from under counter (grip from under door) far enough to expose springs (one on each side). Take care to feed all connecting lines smoothly through cabinet opening.
Note how existing springs are installed.
Install new spring in the same fashion as the old spring was installed.
Test the door operation.
Push unit back under counter taking care to draw connecting lines back through cabinet opening.
Readjust leveling legs as needed.
Reattach unit to counter top.
Reattach water supply and open valve.
Check for water leaks both at valve and under unit, fix as necessary.
Replace panel under door.
Replace any clips inside cabinet.
Reconnect power
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from WEST SUFFIELD, CT
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
No directions with parts!
Could not take apart the upper rack on my whirlpool dishwasher to replace its wheels to transport its upper rack. The received parts did not match the old ones. Called parts and they suggested these new parts remanufactured and changed from the old ones but they had not been notified. Brought to professional mechanics and they figured it out. Bullshit parts company!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from TRINIDAD, CO
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers
I can not get the part to fit and stay in place.
It is a small plastic piece which serves as a stop on the right side of the upper rack. It is the correct part because it is identical to the left one of the same type. I tried clamping down with a pair of pliers but I am afraid of breaking it. With shipping this two inch piece of plastic cost $20, so I do not want to crack it. I am at a loss as to how to sit in in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Shakopee, MN
- Parts Used:
- W10518394
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Dishes would not dry
First i turned off the water and the power, then removed the two screws to the access panel under the door. Then remove 1 screw to the electrical box and removed the wire nuts and pulled the cable out of the box. Then disconect the water supply which is up front, but very little room to work. I didn't have to diconnect the drain hose because it was long enough for me to pull out the machine. After removing to screws that hold the machine to the counter you can pull it out. Remove 2 wire from the terminals of the heat coil. Unscrew the plastic nuts from the washer and remove. Assemble in reverse order and check for leaks. I tested the old element as well as the new element for resistance before installing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carole from IRVINE, CA
- Parts Used:
- WP8565925
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Roller wheel broke off upper rack and also end rack stops needed replacing.
Husband watched your repair video. Everything went well and we are very pleased.
Was this instruction helpful to you?
Thank you for voting!