IUD7070DS3 Whirlpool Dishwasher - Instructions

Remove and replace by hand, no tools required

Our experience was amazing. The part itself simply needed to be replaced: dropped into the lower rack and it was done. The amazing part was the wonderful service that this site provided. We discovered our initial mistake, contacted the company, and received instructions for how to return it. Then we ordered the tine and it was sent immediately. Just received confirmation that the returned lower rack had been received, so the process is complete to our great satisfaction. This site really has it down for providing excellent customer service. They are terrific!! Thank you!

Watched YouTube first of course. Pulled off the old gasket, found the center of the new gasket and started installing the gasket from the very top and all the way down the sides. I made sure it was in tightly and smooth. No more leak, should have listened to my wife sooner!

Pulled out old gasket, pressed in new starting middle top. No more leak.

Followed very simple instructions to easily install. The only tool needed was a flathead scredriver to pop off caps to remove old, broken rollers. New rollers simply click into place. Piease aren't cheap, but significantly less than a new dishwasher.

Turned water off. Removed dishwasher from under the counter, replaced hose, reinstalled dishwasher under the counter.

based on advice here, concluded the problem was likely that the part "Valve-Inlt" was defective. Our dishwasher intake line is copper and had already developed a partial kink from sometime in the past, so I had to be careful. The final connection to the new part had to happen in place: very close to the floor and underneath, because I didn’t want to stress the copper line. Plus, the shutoff was defective, and it was always leaking while I connected. Awkward. As I was threading on, it started to look like it might be cross-threaded, so I stopped and reversed. Slid the washer back out and disconnected the drain line so I could tip the dishwasher u and inspect. It was going on cross-threaded. Not hard to happen on a metal to a plastic connection. To solve, I carefully made very small bends in the copper inlet line until when it would later be brought up underneath to connect to the inlet valve, it would be as perfectly aligned as possible. This worked. As I tightened, it went a little easier and the leak stopped. A good moment. Tightened a bit more, but didn’t want to overdo it as that can cause other problems. Now the moment of truth: let’s run it. DISHWASHER WORKED AGAIN. Runs fine now and we are glad to have it back. Was satisfying I could do this on my own. The advice and guides here made that possible. Thank you.

just replaced broken piece ,,,, very easy ,,, will use you again for parts should the need arise

Very simple to repair The front track stops just slide into place, easy. When I looked for these parts this place was the least expensive and the quickest delivery I have ever had. Quick, efficient and friendly online staffing. Thank you, Deb

It is easy to change out the part. It seems though the part does not freely spin like it should. Does not seem to be warped but does not free spin.
Maybe the new part does not match??

Husband is wonderful, tipped dishwasher over on back, disconnected hoses, and drain motor (replaced that a couple years ago), popped out old part, popped in new part. Had me help him keep door open when working from the inside, and flip a plastic holder piece into place on outside. 15 minutes later, I had a dishwasher that worked like new again.

I'm the maintenance supervisor at an apartment complex. While installing a new dishwasher for a tenant, I inadvertently cross-threaded the swivel connector to the fill valve. The valve was ruined and couldn't be repaired. I ordered a new valve (it was an OEM) and installed it. Simple switch out, plus the video from Parts Select showed I had done it right.

I followed installation instructions from this site and all went well.

I checked the manual to determine the code meaning for 7 blinks, it was heating issue. I ordered the part from Partselect.com. When the part came in, I googled the internet for "How to replace a dishwasher heating element". There were several options, I chose one that was a video showing a handyman go through each step. I followed the steps, with no problems, and WA-LA! Felt good (as the wife of the house) to do it myself!

Tipped over washer, removed attachment bolts, installed new pump by clamping water hoses. Be sure to use proper crimping pliers, not the generic slip joint pliers. Replacement pump included required new clamps.