IDF320PAFW0 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from DEVINE, TX
- Parts Used:
- W10518394
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Wrench (Adjustable)
Element was no longer working. Dishes were not drying.
Watched a video and seen how easy it was to repair. Just disconnect the power, water and return drain. two bolts and replace element . The difficult part was removing and replacing the dishwasher...piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from IONIA, MI
- Parts Used:
- W11169039
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
cut wire in center sprayer to remove plastic holder for new basket
after that every thing went very well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marie from Hollywood, FL
- Parts Used:
- W10518394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
water not heating,dishes not drying
My husband did this. He turned the dishwasher upside-down, disconnected the wires,and unbolted the heater.He put in the new heater (bolted,wired) and tested the current. Voila!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eladio from LOGAN, OH
- Parts Used:
- WPW10538166
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Develeoped a leak on the bottom.
Pulled dishwasher out of compartment, removed all parts underneath. removed inner parts, removed pump assembly. Installed new pump assembly and grommet. Reassembled in reverse order, test ran and unit was operating normal and no leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from SANFORD, NC
- Parts Used:
- W10846093
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Old recirc pump failed
It is a bit difficult to align the grommet, hose, and mounting arm. Suggest using a little vasoline in bushing for the mounting arm/support. it really helps slide in the arm into that bushing so you can get the grommet and hose lined up.
Also, instead of using the supplied hose clamp, suggest using an automotive style hose clamp if you don't have the special tool for tightening the supplied clamp.
Also, instead of using the supplied hose clamp, suggest using an automotive style hose clamp if you don't have the special tool for tightening the supplied clamp.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from WEST SUFFIELD, CT
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
No directions with parts!
Could not take apart the upper rack on my whirlpool dishwasher to replace its wheels to transport its upper rack. The received parts did not match the old ones. Called parts and they suggested these new parts remanufactured and changed from the old ones but they had not been notified. Brought to professional mechanics and they figured it out. Bullshit parts company!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from DOWNS, KS
- Parts Used:
- 4317824
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Someone had used the wrong type of power cord
Recently bought a whirlpool dishwasher, the dishwasher was converted to a portable dishwasher and they did not use the cord application power cord so they machine was blowing our breaker, instructions were very simple and installation was easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from PEMBROKE PNES, FL
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Top rail stop clip broke
Very easy to remove the broken one and just clip in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from TRINIDAD, CO
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers
I can not get the part to fit and stay in place.
It is a small plastic piece which serves as a stop on the right side of the upper rack. It is the correct part because it is identical to the left one of the same type. I tried clamping down with a pair of pliers but I am afraid of breaking it. With shipping this two inch piece of plastic cost $20, so I do not want to crack it. I am at a loss as to how to sit in in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from SACRAMENTO, KY
- Parts Used:
- W11084121
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
would not shut off.
easy the sensor was on the right side, and easy to get to, I turn off the power, turned off the water, and pulled it out, the first thing I saw was the yellow wires and plug. took about 5 minutes, to replace it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Springhill, FL
- Parts Used:
- W10518394
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
element not working
laid dishwasher on its side and unscrewed element. returned unit upright & replaced element. reversed process and reinstalled unit under cabinet
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from GLADSTONE, MO
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Front Track stop missing
Snap new track stop into place. Took a few minutes to figure out top/bottom and inside/outside, but no issues
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from HOPEWELL JCT, NY
- Parts Used:
- WPW10340527
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water was not cleaning dishes on bottom tray.
I noticed the spay arm had some lose. I removed the old spay arm and noticed that the locking nobs broke off the arm and it would not tightly attach to the water outlet in the bottom of the dishwasher. I looked up the dishwasher model number, several diagrams of the dishwasher were offer. I review them and selected the Spay Arm part. It came in 3 days. I attached the spay arm and it snapped into place. Problem solved for less than $60.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Des Moines, IA
- Parts Used:
- 8269144A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Dish washer was very smelly.
After replacing garbage disposal. I referred to you video you sent me when i received the new replacement hose. That made it look very easy to install. Thank you for all your help and support.
Was this instruction helpful to you?
Thank you for voting!