IUD3100BW4 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- al from Fuquay Varina, NC
- Parts Used:
- WP8565925
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
Dishwasher circulation pump malfunction
Tipped over washer, removed attachment bolts, installed new pump by clamping water hoses. Be sure to use proper crimping pliers, not the generic slip joint pliers. Replacement pump included required new clamps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from SUFFOLK, VA
- Parts Used:
- W11768590
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The gasket listed on your website is to thick. So after installation the door would close. I put the old gasket back in the door closed. However, the dishwasher still leaks soap after a cycle..
As stated above the repair did not go well because the gasket was too wide and the door would close. Suggest you talk with Whirlpool about the part they sold you for my model of dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lena from Napoleonville, LA
- Parts Used:
- 8269144A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Leak in hose
Turned water off. Removed dishwasher from under the counter, replaced hose, reinstalled dishwasher under the counter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeanne from Jupiter, FL
- Parts Used:
- W10518394
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench set
Heating element went out, dishwasher wouldn't work
I checked the manual to determine the code meaning for 7 blinks, it was heating issue. I ordered the part from Partselect.com. When the part came in, I googled the internet for "How to replace a dishwasher heating element". There were several options, I chose one that was a video showing a handyman go through each step. I followed the steps, with no problems, and WA-LA! Felt good (as the wife of the house) to do it myself!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicholas from JACKSONVILLE, FL
- Parts Used:
- W11169039
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Upper dish rack broken tines
Swapped out the old upper dish rack with a new one. A video made the change simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rich from hamilton, MI
- Parts Used:
- W10518394
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
bad heater in qiuet partner 2
this job is cake. worst part is removing dishwasher from cabinet. Disconnect water , drain , and power. reove mounting screws in upper door area. Pull unit out and lay it on its face. unplug two wire leads and remove big nuts. Roll unit upright and replace heater. roll unit back over and tighten nuts and plug leads back in. It really takes two minutes to replace heater once the unit is out of cabinet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from The Colony, TX
- Parts Used:
- W10518394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Heater element snapped in two.
Disconnected power,water supply and drain.Had to pull dishwasher out to access the heater element nuts. Removed broken element and replaced with new part. Repair very easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from FRANKSVILLE, WI
- Parts Used:
- WPW10348269
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
would not drain
watch how it was done on computer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Misti from NORMAN, OK
- Parts Used:
- WPW10340527
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Original spray arm was clogged with mineral deposits and not cleaning any loads.
The spray arm repair is super easy. Just click & turn to remove the old arm, repeat to install the new! Less than 2 minutes total time spent on the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from MCMURRAY, PA
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
snap
Just snap it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TRACEY ANN from BRICK, NJ
- Parts Used:
- WPW10195039
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
DISHWASHER WOULD NOT FILL WITH WATER
Unscrewed bottom panel of the dishwasher and simply replaced the bad control switch with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Warren from Ballston Lake, NY
- Parts Used:
- W10728160
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
tine-row rusted and broke
quick and easy,tine-row just snapped right in! Took about 15 seconds!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from JACKSONVILLE, FL
- Parts Used:
- WP8565925
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Stop broke
Looked at how the other was installed oh and bought 2 for when the other one fails. Great customer service!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Mount Washington, KY
- Parts Used:
- 8212560
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher Loose
Installed brackets
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Rapid City, SD
- Parts Used:
- 8212560
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
With qrantz counter top needed to secure dishwasher to side not top of cabinet opening.
Solution was very simple with the side mounting bracket kit, the only problem was somehow one of the brackets was damaged out of the box . There's a slight off-set on the bracket to allow it to fit properly next to the dishwasher but this one had been flatten out. Had to have happened before going into the shipping box because they were very well protected with bubblewrap. Also, brackets are fairly heavy gage metal so it would have taken some amount of force to do this. Fortunately I was was able to bend it back into a useable shape. It wasn't perfect to look at but because it's mounted behind the side of the dishwasher it didn't matter as long as it worked.
Was this instruction helpful to you?
Thank you for voting!