IUD3100BW4 Whirlpool Dishwasher - Instructions

Disconnected the damaged hose extension from the dishwasher outlet drain hose and the connection to the sink drain. Removed two clamps. One a spring clamp and the other a screw clamps. Connected the new extension hose with a spring clamp to the dishwasher outlet drain hose. Connected the other end to the sink drain with a screw clamp. Checked for leaks. Good to go!

The rinse aid cap fixed the problem of leaking rinse aid sta9n9ng the dishwasher every time. What an easy and cheap fix.

Soak up the water in the dishwasher with an old towel. Removed the cover under the dishwasher. Found the pump and twisted it off anti clockwise. Replaced with the new pump. Run a quick cycle, to make sure it pumped out all the water. My wife has used it several times since without any issues.

Put in both a new element and thermostat. Did not fix problem. Using an ohm meter I did not measure any voltage to the thermostat. Suspect it’s a problem in the control unit, and decided to replace dishwasher.

Thanks to everyone for posting their experiences on changing the heater element. The most difficult part of the repair was getting the dishwasher out of the cabinet. I didn't know that I should disconnect the water line underneath the sink and this would make the removal easier. Also, because the copper water line going to the dishwasher was kinked, I ended up changing it with a flexible steel braided line.....much easier to install.

Once the dishwasher was out of the cabinet, I turned it over and easily removed the clips that held the heater element in.

I would definetly recommend people doing this repair themselves, it will save you a lot of money!!!!!

Ordered the wheel on line. It arrived in a day or two. Replacement took 30 seconds.

We are very Happy.

simply line up the new pin with the rectangular slot in the kick panel and metal panel behind, slide the pin in and turn it with a flat blade screw driver.
NOTE: the original pin was black. A black replacement part cost $29 plus shipping! A knock-off pin was only $6 plus shipping. I got the cheap one and colored it with a black Sharpee marker before installation.

The old filter simply unscrews and the new one screws in.

Pulled washer out far enough to put 2x4’s under front feet. Removed front panel, I clipped wire connector and unplugged it. Pushed plastic locking lever in and twisted unit counterclockwise. Wiped inner rim and reversed above procedure to assemble.

removed kick panel with screwdriver, 90 degree turn of screw. Put towel under drain pump. Disconnect drain hose by loosening spring clip with pliers to provide access to pump. released spring clip on old motor while turning counterclockwise to separate pump from drain reservoir. inspect drain reservoir from inside machine to remove any foreign objects. Installed new pump by indexing attachment flanges to notches in reservoir and turning pump clockwise until locking tab makes audible click. reattach drain hose insuring hose is contacting "stop" ribs on drain hose pipe. Run wash cycle on machine to insure there are no leaks. Re-attached kick panel.

Pull dishwasher out a few inches. Disconnect spring from plastic connector with long nose pliers. Remove connector. Replace friction sleeve. Replace connector.Reconnect spring to plastic connector. This completes repair.

I took the valve off and actually hooked 110 volts to the vale and tried to blow through it and it would not let air pass through it. I replaced the the new valve in about 15 minutes and it works fine

I had a common issue on many dishwashers, the final drain cycle was not draining but the pump was trying to turn. Also, the drain pipe was clean. This issue caused a burning smell, like a circuit board heating up. Half plastic smell, half electrical. I bought a replacement pump, followed the pump replacement video instructions from PartsSelect, and it was replaced in under 15 minutes without any tools.

Removed broken tin row. Replaced with new tine row. Tokk less than 1 minute.

The dishwasher stilled filled with water and drained. after verifying that the unit was mostly empty of water, I placed the unit on its back. I removed the main pump leaving the wire terminals in place so I could energize the pump out side of the dishwasher (cut with diagonal cutter). I energized the pump and found that it ran. I noticed that the impellor had significant movement side to side. I suspected that the impellor was jamming in the pump housing. I ordered a new pump from Parts Select. I installed the new pump and reconnected the electrical. The dishwasher operation was restored.