WDT710PAYB5 Whirlpool Dishwasher - Instructions

PULLED BROKEN CLIP OFF AND SQUEEZED NEW ONE IN. I HAD TO USE PLIERS TO SQUEEZE TOGTHER SINCE i AM 77 YEARS OLD AND HANDS ARE NOT THAT STRONG ANY MORE. I HAD ALSO WATCHED THE INTERNET VIDEO TO MAKE SURE I COULD HANDLE THIS CORRECTLY. 10 MINUTES MAX TO UNLOAD TOP RACK AND PUT TOGETHER.

The old filter simply unscrews and the new one screws in.

The air just unscrews with one twist and the new arm twist right back on. No tools needs. Saved me $100 service call.

I had a common issue on many dishwashers, the final drain cycle was not draining but the pump was trying to turn. Also, the drain pipe was clean. This issue caused a burning smell, like a circuit board heating up. Half plastic smell, half electrical. I bought a replacement pump, followed the pump replacement video instructions from PartsSelect, and it was replaced in under 15 minutes without any tools.

Float switch right in front. Did not remove dishwasher. Used small flat screwdriver to un clip cover. Very soft and easy. Unplug and it slides out.
Same with the water inlet. Did not remove and used a screwdriver and small channel locks. Turn off water. Remove hose and remove screw. Slides out. Very easy.

Replaced the strainer. This keeps the two sprayers clean/clear so they do not clog up. Dishes are cleaner now. Note : if your sprayers are clogged it is a long process to clear out the sprayers. Dishes will not be clean until your sprayers are all cleared.

Pulled washer out far enough to put 2x4’s under front feet. Removed front panel, I clipped wire connector and unplugged it. Pushed plastic locking lever in and twisted unit counterclockwise. Wiped inner rim and reversed above procedure to assemble.

Ordered a new pump (after a online diagnosis). Followed the instruction video on the website...also took the time to replace the discharge hose due to residue buildup...tested dishwasher (one cycle). Slide dishwasher back into opening....DONE. Works perfectly. THANKS

First, I checked the ripped box for damage to the dishrack. Fortunately, there was none. Then I looked for the instruction booklet. Unfortunately, there was none. And the parts bag was ripped and I did not know what was supposed to be in it. So, I rechecked the photo of the dishrack on the website and found that either parts were missing or the dishrack was different than illistrated. After a few moments of thought, I realized the latter was the case. I then figured I would have to use some deep thought to do the installation since neither the missing instruction booklet nor the unzoomable photo would help. So, I pulled out the tall thin thingamabob from the old dishrack and put it in the new one though it did not secure as tightly. Then I put the wheel units on just like the old one. What I could not immediately figure out was where the collapsible rack row was mounted. I eventually realized that the rod went into a hole in the wheel units and the latch mounted above one unit. I still have no idea where the two other tan clips go. Though the dishrack is different and thus requires different science to fill it, it appears to do the job.

Thanks for asking.

By the way, it was not blue.

Pull dishwasher out a few inches. Disconnect spring from plastic connector with long nose pliers. Remove connector. Replace friction sleeve. Replace connector.Reconnect spring to plastic connector. This completes repair.

removed kick panel with screwdriver, 90 degree turn of screw. Put towel under drain pump. Disconnect drain hose by loosening spring clip with pliers to provide access to pump. released spring clip on old motor while turning counterclockwise to separate pump from drain reservoir. inspect drain reservoir from inside machine to remove any foreign objects. Installed new pump by indexing attachment flanges to notches in reservoir and turning pump clockwise until locking tab makes audible click. reattach drain hose insuring hose is contacting "stop" ribs on drain hose pipe. Run wash cycle on machine to insure there are no leaks. Re-attached kick panel.

Popping out the old tine rows was very simple and required no tools. The only issue was that the spacing of the replacement tines was different from the original parts and there was not enough space between the tines and the basket to snap the clips back on to hold the tine row. I went to my band saw and cut the extended ends off of the clips and then they snapped into place perfectly. This would have been a 20 minute, no tool job if I didn't have to run to the band saw.

Ordered p/n PS10057154, sold as a kit of TWO upper rack tine rows. I received one. Customer service issued a return tag and ordered a second kit, which again was supposed to be two rows. Replacement order arrived with just one. Fortunately, I had expected this and had not yet returned the first kit. Called customer service and told them not to expect the return of the first order.

This kit is sold as fitting several models of Whirlpool and KitchenAid dishwashers, which I verified that my KA was on the list. A minor installation problem occurred when I discovered that the upright tines of this kit don't have the exact same spacing as the KitchenAid originals. The upright tines need to be exactly half the distance between each of the crossbars on the rack below in order to install the three retaining clips found on each row. With the spacing of these tines, there wasn't quite enough room to install the clips. Fortunately, the retaining clips were manufactured with an excessive amount of shoulder on each one. Trimming off the excess material with a fine-toothed hacksaw blade made the clips narrow enough to be used without compromising their ability to hold the tine rows in place. I've used the machine several times now and the clips are holding everything in place as expected.

[img]https://i.ibb.co/9TQB3mC/clips.jpg[/img]

I took the top dishwasher rack off, then took off the old clip I had taped on. I hadn’t watched the video so I put the new one on by looking at the other side rail and inserted the new part matching the other rail, clicked the new clip on and I was done. it was quite easy for an eighty-one year old woman!! It did take me awhile to figure it out.

Rubber friction sleeves on each side of the door provide resistance to prevent the door from quickly opening when unlatched. Over time the friction sleeve may crack and fail. Two friction sleeves are required for repair. Install a new sleeve on each side of the dishwasher door near the spring connector at the bottom.

Open dishwasher door.

Remove the screw from the left and right bracket at top of dishwasher door opening. Brackets secure the dishwasher to the countertop.

Gently pull the dishwasher forward to expose the door spring on each side of door at bottom.

Unhook the plastic spring connector from the left door spring hook by pulling the connector slightly forward and lifting from the door spring hook. Remove the old friction sleeve if still in place by sliding over the door connection hook. Discard the old sleeve.

Insert the new friction sleeve over the door spring connector hook and push until the friction sleeve is in position completely past the spring hook. Reconnect the plastic spring connector to the door hook.

Repeat for right side of door.

Close and latch the dishwasher door. Unlatch the door. The door should remain in the nearly closed position held in place by the friction sleeves.

Slide the dishwasher back to the original position under the counter top.

Insert the screws in the top brackets to secure the dishwasher.