WDP350PAAB4 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Martin from Union Bridge, MD
- Parts Used:
- WP8268645
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Wheel on lower rack broke.
New one snapped right into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Groton, NY
- Parts Used:
- W11175771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
Stripped the fill valve when installing
I'm the maintenance supervisor at an apartment complex. While installing a new dishwasher for a tenant, I inadvertently cross-threaded the swivel connector to the fill valve. The valve was ruined and couldn't be repaired. I ordered a new valve (it was an OEM) and installed it. Simple switch out, plus the video from Parts Select showed I had done it right.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- al from Fuquay Varina, NC
- Parts Used:
- WP8565925
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
Dishwasher circulation pump malfunction
Tipped over washer, removed attachment bolts, installed new pump by clamping water hoses. Be sure to use proper crimping pliers, not the generic slip joint pliers. Replacement pump included required new clamps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from SNELLVILLE, GA
- Parts Used:
- WP8268866
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Basket was worn though (tray}. Quite old.
Only thing worth saying is that it was a perfect type and fit. Simply lifted the old one out and set the new one in place.
I was pleasantly surprised that it was identical to the old one.
I was pleasantly surprised that it was identical to the old one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dennis from Lisle, IL
- Parts Used:
- W11133712
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Circulation pump very noisy....something wasn't correct
Followed whirlpool Youtube available for DIY.
Caution....ensure that the pump POWER plug does not loosen when reinserting the pump/drain/filter (middle of dishwasher bottom). The plug can get offset if it hits the electrical conduit or water feed/drain hoses under the dishwasher.
Minimal water when disconnecting drain hoses...have towels at the ready.
Again, follow the Youtube video!
Caution....ensure that the pump POWER plug does not loosen when reinserting the pump/drain/filter (middle of dishwasher bottom). The plug can get offset if it hits the electrical conduit or water feed/drain hoses under the dishwasher.
Minimal water when disconnecting drain hoses...have towels at the ready.
Again, follow the Youtube video!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeanne from Jupiter, FL
- Parts Used:
- W10518394
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench set
Heating element went out, dishwasher wouldn't work
I checked the manual to determine the code meaning for 7 blinks, it was heating issue. I ordered the part from Partselect.com. When the part came in, I googled the internet for "How to replace a dishwasher heating element". There were several options, I chose one that was a video showing a handyman go through each step. I followed the steps, with no problems, and WA-LA! Felt good (as the wife of the house) to do it myself!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Felix from MELBOURNE, FL
- Parts Used:
- WP8565925
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Timer repairs
Well, it’s very easy to repair. But, what I like if ur Company is, the availability, of the parts.
Thanks you.
Thanks you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from HUNTINGTON, WV
- Parts Used:
- W11133712
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Pump quit working
Removed the old pump, got part number from it, ordered the part. Simply a matter of slipping the new pump into place, reconnecting the electric, testing the machine out to make sure it did not leak. Then slid back in place with the cabinets.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from BOULDER, CO
- Parts Used:
- W10518394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Dishwasher was not drying the dishes.
I followed installation instructions from this site and all went well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SAMUEL W from SARASOTA, FL
- Parts Used:
- W11768590
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Leak around door
Pulled out old gasket, pressed in new starting middle top. No more leak.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RONALD from EAST GREENWICH, RI
- Parts Used:
- W11752368
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Tines where falling off old rack
The dishwasher is 25 years old. Ordering the part was simple. Very good web site and user friendly. The shipment and delivery perfect. Part arrived as predicted. Tracking delivery was also perfect. Part was exactly what I needed. The only hitch was that there were no instructions for assembly, not even a drawing of the assembly to give a hint as how to assemble. Therefiore assembly took longer than it should have. However the diswasher is back in operation and I am pleased with the results.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tahir from ARLINGTON, MA
- Parts Used:
- W10888592
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replacing upper rack rollers
Followed very simple instructions to easily install. The only tool needed was a flathead scredriver to pop off caps to remove old, broken rollers. New rollers simply click into place. Piease aren't cheap, but significantly less than a new dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from SACRAMENTO, CA
- Parts Used:
- W10888592
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Upper dishrack roller assembly in slide rail broke, causing upper dishrack to sag
I used a flat blade screwdriver to compress one arm of the endcap of the slide rail to free it. I then slid up the locking slide of the old roller assembly freeing it from the upper basket,and put the new part in its place. I then put the roller back in the slide rail and replaced the endcap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from WILLARD, OH
- Parts Used:
- W11768590
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old door gasket was leaking.
Watched YouTube first of course. Pulled off the old gasket, found the center of the new gasket and started installing the gasket from the very top and all the way down the sides. I made sure it was in tightly and smooth. No more leak, should have listened to my wife sooner!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from JACKSONVILLE, FL
- Parts Used:
- WP8565925
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Stop broke
Looked at how the other was installed oh and bought 2 for when the other one fails. Great customer service!!!!
Was this instruction helpful to you?
Thank you for voting!