WDP350PAAB5 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Scott from Oak Harbor, OH
- Parts Used:
- WPW10254672
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The original faucet adapter for portal dishwasher kept misting water out the sides of the adapter most annoyingly.
So I decided to stick in some CLR to see if it would clean it up. Well it got considerably worse. So ordered the new faucet adapter, threaded adapter and the two washers, due to not knowing what i would need. It came like unbelievably fast considering it was Christmas time. Unscrewed the old one from the faucet, screwed on the new one. hooked up the dishwasher, watched it for a bit for any leaks at the connection, and it worked great! I seem to have more water pressure too coming from the sink faucet. Thank you so much for the quickness in sending out my order! -- Scott
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheila from FAYETTEVILLE, NY
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lost stop from one side of top rack. Rack could be pulled off track.
Looked at other side of top rack which still had the stop. Just had to orient the direction of the stop and push it firmly onto the rack arm. Took a couple tries, but it went in and locked. Works perfectly. Inexpensive and easy fix to to very annoying problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jm from OSHKOSH, WI
- Parts Used:
- WP8268961
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Friction sleeve had torn, resulting in dishwasher door 'falling' when opening.
I unscrewed the dishwasher from the counter (two screws under the countertop), and pulled it out about a foot so I could access the friction sleeve. I used a needle nosed pliers to slip a spring latch off the door. Then I slipped the new friction sleeve on and reattached the spring. Tested the door. Success! Super easy. About 5 minutes of work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn from WINTERPORT, ME
- Parts Used:
- WPW10524919
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rinse aid cap was melted when it came out of the designated spot and melted against the heat coil.
Open the washer door, remove old rinse aid cap. Place new cap into designated spot, screw into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darlene from SAVAGE, MN
- Parts Used:
- WPW10524919
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
What a Difference
The rinse aid cap fixed the problem of leaking rinse aid sta9n9ng the dishwasher every time. What an easy and cheap fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from SANFORD, NC
- Parts Used:
- WPW10538166
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
I damaged the grommet when removing the recirc pump
repair went smooth for the grommet. suggest a small of vasoline to ease installation of grommet
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Lebanon, CT
- Parts Used:
- W10518394, WPW10477552
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Dishwasher wouldn't work
Looked under machine, saw wire going to heater was burned off.Seal on heater failed, water leaked onto terminal, shorted and burned, ruined plastic terminal nut.Replaced heater and wire terminal, and nut, took minutes, works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KEVIN from BEL AIR, MD
- Parts Used:
- W10876537
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Was not draining, did not hear motor
Installed new pump from the front. Power off remove front cover reached my hand behind pump for release clip, push down turned counter clockwise pump comes out. Disconnected electrical plug attached plug to new pump. Put pump in at 45 degrees rotated clockwise until hear clip lock in . Tested then replaced cover
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from DOYLESTOWN, PA
- Parts Used:
- W11175771, WPW10195536
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher would not fill with water
The water valve float lever was broke. So I replaced that and the water level switch. Probably didn’t have to replace switch. Very easy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LINDA from ROSEVILLE, CA
- Parts Used:
- WP8268961
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The door had no resistance when opening it
You only need to pull it out about 6 to 8 inches and you don’t need to disconnect anything to slide it on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Indianapolis, IN
- Parts Used:
- W11752368
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The dividers were breaking off the top rack of our dishwasher. Order new rack and installed in minutes. Works great.
Took out old rack by twisting the rack supports. Used old supports because in good shape. Removed the wand from old rack and placed on new rack. Then replaced the supports. Worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dwight from KENT, WA
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
One of the old stops broke
Snapped the new stops on. It took about 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Daleville, AL
- Parts Used:
- W10518394
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
The dishwasher would not dry (heat)
First I identified the problem by checking the plug ends of the heater coil with an ohm meter. I quickly odered the part and when it arrived a few days later, I simply pulled off the electrical connectors, unscrewed the two bolts, removed the old/broken coil, put in the new coil and tightened down the nuts snuggly.
Nothing to it. I then had to reset the error code and it is working like new.
Nothing to it. I then had to reset the error code and it is working like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hector from RCH CUCAMONGA, CA
- Parts Used:
- W10876537
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Drain pump Plastic impeller broke inside
Located drain pump under dishwasher disconnected electrical from wall and pump twisted pump to remove, and installed new pump. Great customer service from Parts Select, helped to make sure i was ordering the correct part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from SAINT CHARLES, MO
- Parts Used:
- W10872845
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
New filter
Ordering the part was very easy. It shipped fast and delivered over 3 days. It fit perfectly
Was this instruction helpful to you?
Thank you for voting!