WDP340PAFW0 Whirlpool Dishwasher - Instructions

After bailing out the unit, filled filter hole with a moderate amount of Dawn dish washing detergent. Ran dishwasher twice to remove all Dawn from the unit. Had to bailout the water (and suds) from the washer both times. After the dishwasher finally drained I inserted the new filter..

So I decided to stick in some CLR to see if it would clean it up. Well it got considerably worse. So ordered the new faucet adapter, threaded adapter and the two washers, due to not knowing what i would need. It came like unbelievably fast considering it was Christmas time. Unscrewed the old one from the faucet, screwed on the new one. hooked up the dishwasher, watched it for a bit for any leaks at the connection, and it worked great! I seem to have more water pressure too coming from the sink faucet. Thank you so much for the quickness in sending out my order! -- Scott

repair went smooth for the grommet. suggest a small of vasoline to ease installation of grommet

Open the washer door, remove old rinse aid cap. Place new cap into designated spot, screw into place.

I unscrewed the dishwasher from the counter (two screws under the countertop), and pulled it out about a foot so I could access the friction sleeve. I used a needle nosed pliers to slip a spring latch off the door. Then I slipped the new friction sleeve on and reattached the spring. Tested the door. Success! Super easy. About 5 minutes of work.

Installed new pump from the front. Power off remove front cover reached my hand behind pump for release clip, push down turned counter clockwise pump comes out. Disconnected electrical plug attached plug to new pump. Put pump in at 45 degrees rotated clockwise until hear clip lock in . Tested then replaced cover

The water valve float lever was broke. So I replaced that and the water level switch. Probably didn’t have to replace switch. Very easy!!

Snapped the new stops on. It took about 2 minutes.

Ordering the part was very easy. It shipped fast and delivered over 3 days. It fit perfectly

You only need to pull it out about 6 to 8 inches and you don’t need to disconnect anything to slide it on

First I identified the problem by checking the plug ends of the heater coil with an ohm meter. I quickly odered the part and when it arrived a few days later, I simply pulled off the electrical connectors, unscrewed the two bolts, removed the old/broken coil, put in the new coil and tightened down the nuts snuggly.
Nothing to it. I then had to reset the error code and it is working like new.

First I got online to troubleshoot issue to save mysel from a service call. One of the first UTube videos, a young man said usually the main issue was the lever. He pushed down on the floater. If it didn't click, than the lever below needed to be replaced. Most important to turn off the circuit breaker before beginning the repair. I got on whirlpool.com, Part Select, ordered the lever, which was under $10. And once delivered, was able to switch out the old lever with the new replacement. Part Quote video took me through the process step by step. The lever package was marked that usually it was only 2% of the time that replacing the lever fixed the issue. Of course, I was thrilled, my dishwasher was up and running again. Thank you.

Removed the bottom plate/cover. Unscrew top from bracket. Lucky,had just enough room to pull washer out. Only 6 in. Sleeve had broken off. Needle nose plyers to unhook spring. Slide sleeve over hinge. Hard Part///. Pull spring back into place. with door shut. good luck.

I removed the lower front panel of the dishwasher to expose wheels and opened door and removed two screws holding washer to cabinet. After raising leveling feet pulled washer out to expose bnotton ow dishwasher. Removed the electrical wires form the heating element and removed screw caps holding the heaqting element in place. Removed the old element and inserted the new, then reversed process to get it back together. It was very easy to do following the instructions I received when I ordered the part.

Located drain pump under dishwasher disconnected electrical from wall and pump twisted pump to remove, and installed new pump. Great customer service from Parts Select, helped to make sure i was ordering the correct part.