WDP350PAAB6 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ken from PEMBROKE PNES, FL
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Top rail stop clip broke
Very easy to remove the broken one and just clip in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from SACRAMENTO, KY
- Parts Used:
- W11084121
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
would not shut off.
easy the sensor was on the right side, and easy to get to, I turn off the power, turned off the water, and pulled it out, the first thing I saw was the yellow wires and plug. took about 5 minutes, to replace it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Springhill, FL
- Parts Used:
- W10518394
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
element not working
laid dishwasher on its side and unscrewed element. returned unit upright & replaced element. reversed process and reinstalled unit under cabinet
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from GLADSTONE, MO
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Front Track stop missing
Snap new track stop into place. Took a few minutes to figure out top/bottom and inside/outside, but no issues
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from MILLBURY, MA
- Parts Used:
- W11175771
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Dishwasher wasn’t getting water.
I located the water inlet valve underneath. After moving the dishwasher out from the cabinet, I tilted it . Then I disconnected the black hose with the pliers . Using the adjustable wrench I unscrewed the water feed to the valve . I then unscrewed the valve from the frame and disconnected the wire plug by unlocking and slipping it away from the valve. To install I did all this in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from WEST SUFFIELD, CT
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
No directions with parts!
Could not take apart the upper rack on my whirlpool dishwasher to replace its wheels to transport its upper rack. The received parts did not match the old ones. Called parts and they suggested these new parts remanufactured and changed from the old ones but they had not been notified. Brought to professional mechanics and they figured it out. Bullshit parts company!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from LAVALE, MD
- Parts Used:
- W10842407
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No problem
Took old ign. swicth of an put newen on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Cape Coral,, FL
- Parts Used:
- WP8268866
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
Missing silverware basket.
I entered the make and model of the dishwasher into the parts store. The part was located and ordered. Received the part a few days later. Fast, efficient way to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dawn from MELBOURNE BCH, FL
- Parts Used:
- WP8565925
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
Top rack broke
I had to replace the whole sliding system on the top rack. Plus the clips holding it. It snapped. I watched the video and did the steps from Steve. The rack slides better than when brand new. Whirlpool wouldn’t pick up phone but part select did. So thank you for being there so I could fix the rack and be able to use the dishwasher again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carole from IRVINE, CA
- Parts Used:
- WP8565925
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Roller wheel broke off upper rack and also end rack stops needed replacing.
Husband watched your repair video. Everything went well and we are very pleased.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from LAKE GEORGE, NY
- Parts Used:
- WP8565925
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
I needed to add a clip stop to the right front track.
I manually attached the track stop to the right track in the disheasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bart from Ellicott City, MD
- Parts Used:
- W10876537
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
dishwasher didn't drain.
Replaced the pump.That wasn't the problem --- if I had it to start over, I'd pull the drain hoses and run the dishwasher to see what water is flowing where. I had a clogged drain --- and maybe something else. Still working through the details.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rich from boulder city, NV
- Parts Used:
- W10518394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
heater showing signs that it was going to fail soon
removed unit from cabinet disconnected water and drain lines replaced heater very easy to do it took more time to remove unit from under counter than replace heater piece of cake..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from RIVERSIDE, IL
- Parts Used:
- W11175771
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
The Inlet Valve cracked from the severe cold weather we had in Chicago area.
Removing and installing the new part was fairly simple. We removed the water hose first since it is the easiest to see. We then removed the screw holding the part to the metal frame. We slid out the part out of the holder to remove the black hose and electric plug (it is like the old phone jacks). After it was completely off we plugged in the electric to the new part which was very easy since it can only go in one way. We slid the new part in place and attached the black hose. We attached the piece to the frame with the one screw and last we attached the gold (garden hose) connection. We turned on the water to look for any leaks then turned the power on and ran it through a partial rinse to be sure there were no leaks.
Was this instruction helpful to you?
Thank you for voting!