WDP350PAAB3 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Walter O from CROYDON, PA
- Parts Used:
- WPW10348269
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dishwasher would not empty.
Ordered a new pump (after a online diagnosis). Followed the instruction video on the website...also took the time to replace the discharge hose due to residue buildup...tested dishwasher (one cycle). Slide dishwasher back into opening....DONE. Works perfectly. THANKS
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from NEPTUNE, NJ
- Parts Used:
- WPW10224430
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Soap Dispenser No Longer Functioning
Repair was easy. Step by step instructions on touTube
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from WAUKEE, IA
- Parts Used:
- WP8268961
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Friction sleeve came apart ....would not hold door in place
Pull dishwasher out a few inches. Disconnect spring from plastic connector with long nose pliers. Remove connector. Replace friction sleeve. Replace connector.Reconnect spring to plastic connector. This completes repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from OXFORD, MI
- Parts Used:
- WPW10348269
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
drain pump noisy, broken piece of glass caught in pump.
removed kick panel with screwdriver, 90 degree turn of screw. Put towel under drain pump. Disconnect drain hose by loosening spring clip with pliers to provide access to pump. released spring clip on old motor while turning counterclockwise to separate pump from drain reservoir. inspect drain reservoir from inside machine to remove any foreign objects. Installed new pump by indexing attachment flanges to notches in reservoir and turning pump clockwise until locking tab makes audible click. reattach drain hose insuring hose is contacting "stop" ribs on drain hose pipe. Run wash cycle on machine to insure there are no leaks. Re-attached kick panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from CLINTWOOD, VA
- Parts Used:
- W11175771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
clean light blinked 4 times and repeated this over and over
I took the valve off and actually hooked 110 volts to the vale and tried to blow through it and it would not let air pass through it. I replaced the the new valve in about 15 minutes and it works fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Wichita, KS
- Parts Used:
- W11752368
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Upper dishrack needed replaced
I removed the upper dishrack easily by removing the end clips and sliding the tray out. Removal of the revolving sprayer was easy as it just clipped on to the bottom of the rack. The rack was not the rack that was ordered and I was informed that this was the correct rack for the dishwasher even though the description and picture was different that what I received. There were no instructions with the rack to explain how to attach the "flaps" that can go over lightweight dishes to keep them from flipping. Every way I tried to attach the flaps did not work. When I was able to attach one it would pop off if I raised the flap to place a dish underneath it. I finally gave up on the flaps and reinserted the rack onto the rails and put the end clips back in place. The rack works fine other than it is not the one that was described and was not the rack that I wanted.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Redmond, OR
- Parts Used:
- WPW10224430
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
soap dispensor door was warped
The repair was easy, no instructions with the part. I had a bad leak the first go round, found out that I did not have it centered with-in the indentation on the door panel, so I got to install it twice.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from BATON ROUGE, LA
- Parts Used:
- WP8268961
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher door drops quickly to wide open position when unlatched
Rubber friction sleeves on each side of the door provide resistance to prevent the door from quickly opening when unlatched. Over time the friction sleeve may crack and fail. Two friction sleeves are required for repair. Install a new sleeve on each side of the dishwasher door near the spring connector at the bottom.
Open dishwasher door.
Remove the screw from the left and right bracket at top of dishwasher door opening. Brackets secure the dishwasher to the countertop.
Gently pull the dishwasher forward to expose the door spring on each side of door at bottom.
Unhook the plastic spring connector from the left door spring hook by pulling the connector slightly forward and lifting from the door spring hook. Remove the old friction sleeve if still in place by sliding over the door connection hook. Discard the old sleeve.
Insert the new friction sleeve over the door spring connector hook and push until the friction sleeve is in position completely past the spring hook. Reconnect the plastic spring connector to the door hook.
Repeat for right side of door.
Close and latch the dishwasher door. Unlatch the door. The door should remain in the nearly closed position held in place by the friction sleeves.
Slide the dishwasher back to the original position under the counter top.
Insert the screws in the top brackets to secure the dishwasher.
Open dishwasher door.
Remove the screw from the left and right bracket at top of dishwasher door opening. Brackets secure the dishwasher to the countertop.
Gently pull the dishwasher forward to expose the door spring on each side of door at bottom.
Unhook the plastic spring connector from the left door spring hook by pulling the connector slightly forward and lifting from the door spring hook. Remove the old friction sleeve if still in place by sliding over the door connection hook. Discard the old sleeve.
Insert the new friction sleeve over the door spring connector hook and push until the friction sleeve is in position completely past the spring hook. Reconnect the plastic spring connector to the door hook.
Repeat for right side of door.
Close and latch the dishwasher door. Unlatch the door. The door should remain in the nearly closed position held in place by the friction sleeves.
Slide the dishwasher back to the original position under the counter top.
Insert the screws in the top brackets to secure the dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from CASTLETON, NY
- Parts Used:
- WPW10254672
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Portable Dishwasher was leaking around connection to faucet.
Purchased and installed new faucet attachment. It arrived quickly and very easy to attach. Thank you !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Pipersville, PA
- Parts Used:
- WPW10224430
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Detergent dispenser was broken.
Replaced the detergent dispenser using the directions on the shipping notice.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from MILLBURY, MA
- Parts Used:
- W11175771
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Dishwasher wasn’t getting water.
I located the water inlet valve underneath. After moving the dishwasher out from the cabinet, I tilted it . Then I disconnected the black hose with the pliers . Using the adjustable wrench I unscrewed the water feed to the valve . I then unscrewed the valve from the frame and disconnected the wire plug by unlocking and slipping it away from the valve. To install I did all this in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from GLADSTONE, MO
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Front Track stop missing
Snap new track stop into place. Took a few minutes to figure out top/bottom and inside/outside, but no issues
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from PEMBROKE PNES, FL
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Top rail stop clip broke
Very easy to remove the broken one and just clip in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from HOPEWELL JCT, NY
- Parts Used:
- WPW10340527
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water was not cleaning dishes on bottom tray.
I noticed the spay arm had some lose. I removed the old spay arm and noticed that the locking nobs broke off the arm and it would not tightly attach to the water outlet in the bottom of the dishwasher. I looked up the dishwasher model number, several diagrams of the dishwasher were offer. I review them and selected the Spay Arm part. It came in 3 days. I attached the spay arm and it snapped into place. Problem solved for less than $60.
Was this instruction helpful to you?
Thank you for voting!