Models > WDF730PAYT6 > Instructions

WDF730PAYT6 Whirlpool Dishwasher - Instructions

Jump to:

All Instructions for the WDF730PAYT6
16 - 30 of 279
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
J from HARPERSVILLE, AL
Parts Used:
WPW10195536, WP8531323, W10878507
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Water leak
I watched the instructional videos that showed how to replace the inlet fill hose/water inlet a couple of times. The repair was exactly as shown. No trouble at all.
23 of 28 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michelle from Richardson, TX
Parts Used:
72017
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
81 of 209 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Amy from MIDDLEBURG, FL
Parts Used:
W11768590
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Leaking dishwasher
Removed old gasket. Cleaned the area and let dry. Aligned gasket, pressed into the groove. Corners are tricky, stretch and press to get a tight seal. Follow around appliance. Inital try, small leak. Adjusted seal second use no leak. 10/10 would recommend this part. Super easy self install.
18 of 21 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from Winchester, VA
Parts Used:
W10518394
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench (Adjustable), Wrench set
clean light flashing 7 times would not run
removed screws holding dishwasher to counter top,raised leveling pads,pulled dishwasher out, unplugged wiring,removed hold down nuts from inside dishwasher and installed new heater element, this was all easy the hard part was finding the code to reset the dishwasher there was no paperwork inside the dishwasher although there was an empty plastic holder.The code that worked for my model was with the door open to push the normal wash button then the high temp button three times as fast as you can within four seconds then close the door. It worked and reset the dishwasher which ran a short cycle then shut down as normal and is now working fine.After doing this select the beverage of your choice and relax. Hope this helps someone.
18 of 22 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Karen from Great Falls, VA
Parts Used:
W10727422
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Upper Dishrack and tines rusting out
My KitchenAid dishwasher's upper dishrack had several places that were completing rusting out, just leaving the skins of the plastic coating in place. I ordered the upper dishrack - just the dishrack, none of the clips or other items shown in the schematic - and installed it pretty easily. One caution - this is JUST the upper dishrack. If you have two rows of tines that are clipped in and flip-flop back and forth on the left and right wider sides of the rack, you will need to order one or two pieces of part # PS 898500 as well. One of my tine rows was in salvageable shape, so I only needed to order one (in a second order upon discovering I it wasn't included). It wasn't difficult to figure out how the clips could come out and snap back in place. Just be careful, know that these are just plastic items and can break easily.
18 of 23 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David A from Show Low, AZ
Parts Used:
W11158802
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
latch on silverware basket would't lock
bought a new one and put it in machine.
16 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
christopher from MOSES LAKE, WA
Parts Used:
W11032770
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
wash pump stopped working
change out the old pump with new one actually quieter running pump awesome
14 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Shawn from WEIRTON, WV
Parts Used:
WPW10491331
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Lower spray arm worn out
Took less than one minute
15 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Crystal from Stansbury Park, UT
Parts Used:
WP8558307
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
I did not lock the cap good enough and it fell off and melted
I just placed the cap back on, it worked great, fit fine and so glad I found this part. I was thinking of ways to McGyver it, thinking it would be impossible to find a new part. Glad i fount this site and the part.
14 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from BOULDER, CO
Parts Used:
W10619006
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Dishwasher would not turn on and door did not latch properly.
New latch assembly improved door closure. However, door latch did not solve problem. There appears to be another problem.
15 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dave from PALM BAY, FL
Parts Used:
WP8268961
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Friction sleeve
Make sure you order 2. One on each side
14 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paula from ANDOVER, MA
Parts Used:
WPW10340542
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
rubber flaps on the end of the manifold were worn - no pressure
Ordered the "right" part according to the diagram. The part I received was about 1/4" too long so I couldn't use the whole manifold. Took the rubber end off and - fortunately- it fit the old manifold. Dishwasher works fine now. Wish I could have ordered just the rubber valves.
13 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Frederick from BIG PRAIRIE, OH
Parts Used:
WPW10348269
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench (Adjustable)
Water not draining from the dishwasher
I watched the video and this was the easiest repair ever. Took longer to disconnect and reinstall than it did to change out the pump. Highly recommended watching the video
13 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tim from BURTONSVILLE, MD
Parts Used:
WP661566
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
No heat. Replaced thermostat
Was able to replace and repair without taking the dishwasher out. Thermostat is behind and to the left of the power junction box. Has 2 wires going to it. It is up against the bottom of tub. I used an angled mirror to see what I was doing. 1 small screw to detach and pull down thermostat. Be sure power is off before you start. Also reprogrammed defaults. Hit any button 1-2-3, 1-2-3, 1-2-3, fast and close door. Let it sit 15 min to run and re-set defaults. Now I have heat and dry dishes.
13 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Armand from N STONINGTON, CT
Parts Used:
WPW10348269
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Drain Pump was giving off a burning smell. When I pulled the dishwasher out it had some light smoke coming from the Drain Pump
Shut the power to the dishwasher off. Pulled unit out from under the counter top and raised the left hand side up for easy access. Disconnected the wiring, undid the clips, turned counter clockwise and removed. Reversed the order for installation and Connected the power. Ran several cycles successfully. Problem fixed. Burnt out water pump. Good as new if not better so far. Easy item search, Fast Shipping, Quality Part, Fair Pricing. Thank You Partselect.com
13 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WDF730PAYT6
16 - 30 of 279