WDF530PLYM6 Whirlpool Dishwasher - Instructions

After replacing garbage disposal. I referred to you video you sent me when i received the new replacement hose. That made it look very easy to install. Thank you for all your help and support.

My husband did this. He turned the dishwasher upside-down, disconnected the wires,and unbolted the heater.He put in the new heater (bolted,wired) and tested the current. Voila!

laid dishwasher on its side and unscrewed element. returned unit upright & replaced element. reversed process and reinstalled unit under cabinet

1. Open dishwasher door, to access the screws holding dishwasher to cabinet.... remove these screws.
2. May need to shut water off and unscrew water line and waste line (if they aren't long enough because you will need to pull dishwasher out.
3. Unplug electricity
4. Pull dishwasher all the way out... probably need to disconnect the water and waste lines
5. crescent wrench to unscrew the plastic screws in back
6. Disconnect two wires going to element
7. Replace element... reverse steps
8. Not too bad at all
9. Part Select is Awesome !!!!

First i turned off the water and the power, then removed the two screws to the access panel under the door. Then remove 1 screw to the electrical box and removed the wire nuts and pulled the cable out of the box. Then disconect the water supply which is up front, but very little room to work. I didn't have to diconnect the drain hose because it was long enough for me to pull out the machine. After removing to screws that hold the machine to the counter you can pull it out. Remove 2 wire from the terminals of the heat coil. Unscrew the plastic nuts from the washer and remove. Assemble in reverse order and check for leaks. I tested the old element as well as the new element for resistance before installing.

Remove power source, then remove old power cord.Run new power cord through existing opening ang attach to existing power box on bottom o f dishwasher. Install electrical leads and device ground. Reinstall cabinet bottom. Check out operation by running a cycle. All ok!

removed unit from cabinet disconnected water and drain lines replaced heater very easy to do it took more time to remove unit from under counter than replace heater piece of cake..

Since I have All Whirlpool appliances in the home, the only one not a Whirlpool was a counter top dishwasher that looks exactly like it could be a Whirlpool and so not to be the odd unit out, I labeled it with with a Whirlpool logo nameplate on the face of the door. Now everything matches perfectly and all in the same exact color white too.

Just measured and marked where the plate was to be located, cleaned that part of the surface, peeled the backing and carefully placed the logo name plate in place and pressed it on. Voila. Done and looks original as well. Call me the big, deep fakearooski.

just screwed it on

followed directions, a kid could have done it,

1. Remove the top rack
2. Take a screwdriver and pry off back plastic stop at end of track
3. Slide track off, then slide new track on
4. Take the plastic back stop originally pried off of old track and snap into new track
5. Open plastic stop at front of track
6. Replace top rack.
7. Close plastic stop at from of track
8. Good to go!

Removing and installing the new part was fairly simple. We removed the water hose first since it is the easiest to see. We then removed the screw holding the part to the metal frame. We slid out the part out of the holder to remove the black hose and electric plug (it is like the old phone jacks). After it was completely off we plugged in the electric to the new part which was very easy since it can only go in one way. We slid the new part in place and attached the black hose. We attached the piece to the frame with the one screw and last we attached the gold (garden hose) connection. We turned on the water to look for any leaks then turned the power on and ran it through a partial rinse to be sure there were no leaks.

No tools needed except a knife to open the box. It just snapped into place. Probably took all of 60 seconds. Now the tray rolls out and in like new.

installed a new rack

Kit didn't have the center conical piece. Easy to switch tho. I am impressed at the speed of which the part arrived.