WDT970SAHB0 Whirlpool Dishwasher - Instructions

Gently pull the old door seal out of it's track observing the orientation of the seal and the amount of extra seal at the ends of the seal grove/track..
Start installing the seal on one side leaving about the same amount of extra seal as original seal before removal.
Be sure the seals orientation is the same as the seal that was removed.
Carefully pressing the seal into the grove/track designed to hold the seal. Be careful to fully seat the seal into the grove/track.
The corners will be a little tricky, but carefully press and seat the new door seal all the way around. There should be a little extra seal after you get to the end of the grove/track.
Good luck, the new door seal solved my water leak.

Snap in the missing track stop and twist snap the middle spray arm. That simple.

Disconnected the damaged hose extension from the dishwasher outlet drain hose and the connection to the sink drain. Removed two clamps. One a spring clamp and the other a screw clamps. Connected the new extension hose with a spring clamp to the dishwasher outlet drain hose. Connected the other end to the sink drain with a screw clamp. Checked for leaks. Good to go!

Pull the old seal out and push the new seal in. Done. Easy. The only issue is the door is still leaking and I have to replace the seal and the plate that goes across the bottom of the door.

Order both this seal and the seal for the bottom of the door at the same time.

I opened the package took out the replacement part and installed it with no tools. Easy, done in 10 minutes.

This is the second time I have replaced a rack. You just pop on the new rollers and you're good to go!

With a little pressure, I was able to push off the broken wheel pieces with my thumbs. I was able to snap on the new wheel pieces really easily.
This job took less than 15 minutes to replace all 4 wheel pieces.

I read how other people had the same problem, I checked everything that could possibly cause this. I then believed I knew what was wrong. I ordered a new arm. It was unbelievable how easy it was to replace.it. It took less time than a minute. . Turn the nut holding the arm counter clockwise to remove the arm. To replace turn the nut clockwise I now have a working dishwasher. It is not necessary to remove the dish rack.

simply line up the new pin with the rectangular slot in the kick panel and metal panel behind, slide the pin in and turn it with a flat blade screw driver.
NOTE: the original pin was black. A black replacement part cost $29 plus shipping! A knock-off pin was only $6 plus shipping. I got the cheap one and colored it with a black Sharpee marker before installation.

My wife hired a local repairman when the right side spring cable broke (I was out of town). He took two hours to fix it (and two appointments). The door would then pop open when running. He came back and replaced the latch. Problems persisted. I then ordered new hinges and replaced both in half hour or so. Would recommend doing all of these repairs yourself. None of these repairs are that hard and definitely not worth paying hundreds to do it. Trickiest part is pulling the dishwasher out from the counter without impacting the electrical or water connections. Disconnecting the power is important on all repairs. When you take the screws out of the door to get to the hinges, make sure you have a helper just to hold the door up while removing the last few screws. The left side hinge was really bent (when the right side spring cable broke) - caused the door to be out of square and thus would not effectively close. This was obvious after a 5 minute search on this this and other repair sites. Process that I used: 1. remove screws from both sides holding dishwasher into counter (may have screws into countertop as well). 2. turn off power, 3. pull out dishwasher far enough to see hinges and springs (careful of connections), 4. remove front door screws, 5. take off front panel, 6. remove spring cables (pull cable taut and remove "hook" from hinge)., 7. unscrew two screws holding hinge to door, 8. bend metal fingers around hinge pin to be able to remove hinge., 9. attach hinge in opposite path. 10. repeat on other side (if necessary), 11. reconnect things in opposite order...test door prior to reattaching door panel. Make sure you level the unit with the adjustable feet. Make sure screws in sides of cabinet aren't too tight as it can take the unit out of square pretty easily...

We took the rollers off the old one (new ones came with the dishrack also) and put them on the dishrack (they snapped on). There was also an extra piece that we figured out how to put on. Then slid it in place and it was fine.

Removed the inner panel, remove electrical connection to dispenser, remove dispenser, metal tabs that hold it in, are a bit hard to pry metal tabs, and when installing net dispenser tabs are also a little difficult to pry tabs to install but doable. So far works like it should.

First, I checked the ripped box for damage to the dishrack. Fortunately, there was none. Then I looked for the instruction booklet. Unfortunately, there was none. And the parts bag was ripped and I did not know what was supposed to be in it. So, I rechecked the photo of the dishrack on the website and found that either parts were missing or the dishrack was different than illistrated. After a few moments of thought, I realized the latter was the case. I then figured I would have to use some deep thought to do the installation since neither the missing instruction booklet nor the unzoomable photo would help. So, I pulled out the tall thin thingamabob from the old dishrack and put it in the new one though it did not secure as tightly. Then I put the wheel units on just like the old one. What I could not immediately figure out was where the collapsible rack row was mounted. I eventually realized that the rod went into a hole in the wheel units and the latch mounted above one unit. I still have no idea where the two other tan clips go. Though the dishrack is different and thus requires different science to fill it, it appears to do the job.

Thanks for asking.

By the way, it was not blue.

Due to the way I installed the appliance originally it was not necessary to disconnect supply water nor the drain connections. When the cord broke the spring came out of the point of connection to the appliance. It some "finagelling" to reattach the spring.After some "select vocabulary" it hooked into the correct spot and the rest was history.

1. Remove front of door with torx screws around inside top and sides of door.
2. Unclip and remove plug with two wires for dish soap solenoid. You may have to lie on your back or use a mirror to see the location of the small clip retaining the plug.
3. Unclip and remove dispenser module. Here's the rub: the clips used to retain the unit in the door panel of my dishwasher are tabs cut in the stainless steel cut-out and rolled back at a 90 degree angle to retain their springiness. They seat against the back edge of three plastic ridges along the top, bottom and one along each side of the dispenser module. The key is to remove the module without permanently bending these tabs, thereby losing their springiness and destroying their ability to clip tight against the new module to hold it in. I had some success slipping 3 pieces of flashing under the stainless tabs along the top and sides of the old module, allowing the plastic retaining ridges to ride under the tabs all together and move forward to disengage the clips without permanently bending the tabs.
4. Reassembly is just the reverse.