DP920PFGY3 Whirlpool Dishwasher - Instructions

Crazy Glued it together until we received the new part, but it fell off again. My husband installed the new piece and said it only took him about 2 minutes. You just take off the end cap and pop in the new piece and adjust to match the one on the other side of the rack. He said it was extremely easy and no tools required.

Nozzle cap rubber housing was split and cracked. It simply unscrews. The replacement was a matter of screwing the new nozzle cap on. My wife was trusted with this installation. Believe me, this indicates how easy it was.

As described with instructions, removed original "bearing," installed replacement, removed original spring, installed replacement springs. Not difficult.

THERE WERE NO INSTRUCTIONS INCLUDED, COULDN'T FIGURE 0UT HOW TO INSTALL THE NEW ROLLERS ON THE NEW RACK FINALLY INSTALLED THE OLD ROLLERS ON THE NEW RACK AND THEY WERE MUCH EASIER TO INSTALL I DONT UNDERSTAND
WHY THE NEW ROLLERS WERE THE SAME AS THE OLD ROLLERS
EXCEPT FOR THE COST.

Did not use the new parts. After removing the spray arm, found a screw out of place. Put the seal ring back in place and the screw back in the hole. Machine works like new.

I USED A PLUMBER

I replaced the seals per the video instructions.

So my dishwasher is 20 some years old. Woke up in the morning to smell burning plastic and the dishwasher never moving to the next part in the cycle. I thought it was the high limit, then the cycling thermostat(because cycling you'd think it was cycling wrong). Nope. It was working fine. I used a multimeter to test the high limit(ohm reading will be closed at room temp) and for the cycling(will be open at room temp, so use a multimeter with alligator clips and a lighter to trigger it to close). All of my existing parts were fine. So I went to the timer and tested with alligator clips, each part that connected during the timing cycle. Sure enough. On the rinse and pump water out part, the contact point wasnt connecting due to corrosion and a bent prong. So I rebent it and cleaned all the contact points. All you need to do on these old washers is pull out the timer and pull off the thin plastic "sheild" over the thing. Guess what. I have a working dishwasher after having done the impossible and fixed my timer. So for those who have a dish washer that won't advance, but you can hear your timer advancing with the clicks, this is your problem. Saved myself an unknown amount of money because they don't make my timer anymore.

Since there were no printed instructions, we looked at the photo schematic.
Reassembly using the photo was easy by putting the old rack alongside the new one and adjusting the new rack spacing to match the old one.
We also had new wheels which snapped on.
We were delighted to repair and replace this good, older dishwasher rather than purchase a new one!

Snapped on the rollers, removed the center part from the old rack that sprays the water and snapped it on the new one. We then bent the back row down so it would acomodate my larger items. My old rack had that feature. You could either have the rack up or down. Now l
ooks beautiful and works perfectly.
Could have used some directions though.

Repair went exactly like the video i watched online. Perfect

Both springs (8066018 and 3368999) were replaced as recommended in your troubleshooting guide, but did not resolve the problem. Finally the Dual Motor, 3374501, was replaced. During the above, the plastic face of the door fell off, which created a nuisance task before proceeding to fix the original problem. However, while replacing the motor, I realized the purpose of the two, T-shaped studs sticking out of the motor. It is absolutely necessary that these sit inside the slots which engages the sliding plastic cover, which is spring loaded, in order to engage the release of the soap dispenser door. It was truly a learning experience, but I got it done.

It took all of 30 minutes from beginning to end remove the old parts and replaced them and run a diagnostic test before I could wash dishes. The parts were exact and Parts Select has always provided the right parts, shipped fast and never disappointed me.

Just replaced it in the notches that held the rusted tine.

No tools required except possibly a small screwdriver to help remove stop in end of rack; part easily installed by hand and stop re-inserted. Finished in several minutes. Thanks!