DP940PWPQ2 Whirlpool Dishwasher - Instructions

My dishwasher started leaking at the door. I checked the level, door seal, fill float, etc. Nothing worked. Another reviewer of these parts said to replace the Seal, Lower Sprayarm, the Wash Arm Bearing Ring, and the wash arm. I replaced the seal and the bearing, not the washer arm, as my spray had little to no wear. This fixed the problem! If you dishwasher leaks at the door, it is possible these parts are worn and replacing them wil fix the leak. Thanks to the other reviewer I now have no leaks! Buy a spare nut because they break very easy if overtorqued!

I removed the bottom spray arm and replaced the worn part. Now the arm turned freely and was performing as it was designed to do. I appreciate parts select for having the part available since the manufacturer no longer supported the model.

First I removed the plastic bolt that holds the wash arm in place This exposed the upper ring that was worn out . I then lifted the arm off which exposed the larger ring. I replaced that ring, and then I put the arm back on and replaced the upper ring. I put the plastic bolt back in place and the repair was complete.-- Really Easy plus the dishwasher gets the dishes clean now

I have a new faucet so I remove the screen then I used an extender ring put on your adapter an got the washer to run.

Removed the lower spray arm assembly thumb screw and lifted off the spray arm assembly. The lower seal had disintigrated - couldn't even find any pieces in the filter. After reassembly with the new seal and bearing I turned the spray arm by hand to ensure it was not binding. There was still was, what I would consider, some excessive wobble. I fashioned a shim washer out of some plastic from a Folgers coffee can lid and installed it on the thumbscrew threaded shaft and tightened it all down finger tight - it works very well and now, and no wobble.
I relaced the upper spray arm seal while I was doing the job (both the upper and lower seals are the same part #). I figured it would go out on me eventually, so I might as well replace it while I was doing the lower arm work. Kept the old upper arm seal as an emergency replacement.

Cleaned the filter screen of all debris (it is amazing what collects there over time). Cleaned the stainless tub with some spray Greased Lightning, ran the rinse cycle, and then put a few tablespoons of citric acid crystals in the soap dispenser and ran the dishwasher on NORMAL WASH with temperature boost.
Looks new inside; cleans the dishes, glasses and utensils well (no water spotting); and is nice and quite (like when it was new).

The old spring on the detergent dispenser box door failed and the dispenser door would not pop open at the right time in the wash cycle.

Ordering the new spring was easy on the website. Need dishwasher model number, stock number and serial number.

Hint - Order at least 2 springs! They are not expensive.

I followed the instructions in the video. I could get the spring on the spindle correctly but could not get the two spring prongs to catch to create spring tension on the door without using a thin knife blade to carefully push each prong to where it caught on the dispenser door.

I needed to slide the prongs slowly and carefully to get them to catch on the door. This distorted the spring. That's why you really need two springs. I then used needle nose pliers to pull the latching part of the spring to catch on the inner door. That distorts the spring, too.

So you really need two springs. One spring to learn how to do it and a second one to replace the one you distorted as you learned.

Take care

Purchased and installed new faucet attachment. It arrived quickly and very easy to attach. Thank you !

WATCHED THE VIDEO FOR 2 MINUTES. REPLACED THE 3 PARTS IN LESS THAN A MINUTE. THANKS FOR THE VIDEOS.

Pulled the old gasket out with needle nose pliers, cleaned the slot for the gasket, installed the new gasket, needed no tools. This repair took 5 min.

I ordered a dishwasher soap dispenser "lid assembly". When it arrived, it was not an assembly at all but only a lid. I had to reorder a pin and spring, When i finally had every thing, it was an easy repair.

I bought the kit because it had other parts that I thought I needed.

The 1/4 inch impeller bolt to shaft would not budge with a nut driver so I had to use a ratchet to loosen it. I could not hold the drain impeller with an adjustable wrench so I had to use a vice-grip. This still did not loosen it so I used an oscillating power saw to cut away at the bottom of the drain impeller being careful to only cut so deep, I didn't want to cut into the motor shaft. Once I had cut some grooves into the drain impeller, I could break it into pieces and remove it. Upon reassembly I tightened the 1/4 inch bolt with the ratchet.

Could not take apart the upper rack on my whirlpool dishwasher to replace its wheels to transport its upper rack. The received parts did not match the old ones. Called parts and they suggested these new parts remanufactured and changed from the old ones but they had not been notified. Brought to professional mechanics and they figured it out. Bullshit parts company!!

It is a small plastic piece which serves as a stop on the right side of the upper rack. It is the correct part because it is identical to the left one of the same type. I tried clamping down with a pair of pliers but I am afraid of breaking it. With shipping this two inch piece of plastic cost $20, so I do not want to crack it. I am at a loss as to how to sit in in place.

This spinner is attached to a plastic module PN WP3379369 which is held in place by two screws to the top of the dishwasher. I was able to temporarily reattach the spinner by using a hot soldering iron to melt the nylon axle that goes through the spinner. By using a very small metal washer placed on top of the spinner I was able to melt enough off the end of the nylon axle so as to keep the spinner in place and still be able to rotate. By far the most difficult part of this repair is removing the two stops that prevent the upper washer rack being removed from the machine. Doing so requires using a pair of long nosed pliers and taking note of what needs to be squeezed. Even if installing a new part the upper rack needs to be removed in order to get access to this central part.