WDF780SLYB2 Whirlpool Dishwasher - Instructions

Pulled dishwasher out from under counter. Relaced cord with plastic hook attaching spring to door. Very easy.

Very impressed with Partselect.com. Full schematic of dishwasher made it easy to select part.

Delivered in 1 day. Fantastic. Highly recommend

I purchased this misguided by the official response to "Doug" on April 17, 2018, which at the time was labeled as "most helpful". This is NOT the little grommet in the center. This is a big grommet that goes no the supply pump. This is #14 in the diagram. (#15 is actually the clamp that holds it). If you are looking for the little grommet that goes on that stem on the central recirculation pump, that part is not available, it only comes fused on the sump, and for replacing the sump you have to disassemble the whole bottom part of the dishwasher, pumps, sensors, valves, hose...even this big grommet. A lot of work, and since you are at it, you might want to replace both grommets. If you need THIS big grommet (#14) only, then it is not so much work, just take out one clamp, one connected cable, and the grommet to replace. But check if your machine has reusable clamps, because if not, you might want to order a new clamp. Good luck!

Per the you tube video

I watched the instructional videos that showed how to replace the inlet fill hose/water inlet a couple of times. The repair was exactly as shown. No trouble at all.

Removed old gasket, cleaned track and replaced gasket-also quit using Cascade pellets and went back to using Cascade powder with a numerical "rating" of 6. The pellets of even 10 caused the washer to leak, obviously too much foam would not float the float to actuate the pump.

It was very easy to pry off the old wheel assemblies with a screwdriver and pop the new ones in place. Although the part is called "wheel" it is actually the plastic piece containing two wheels. I thought it was a little confusing to just call it "wheel" as each piece has two wheels. It was an easy repair.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

My KitchenAid dishwasher's upper dishrack had several places that were completing rusting out, just leaving the skins of the plastic coating in place. I ordered the upper dishrack - just the dishrack, none of the clips or other items shown in the schematic - and installed it pretty easily. One caution - this is JUST the upper dishrack. If you have two rows of tines that are clipped in and flip-flop back and forth on the left and right wider sides of the rack, you will need to order one or two pieces of part # PS 898500 as well. One of my tine rows was in salvageable shape, so I only needed to order one (in a second order upon discovering I it wasn't included). It wasn't difficult to figure out how the clips could come out and snap back in place. Just be careful, know that these are just plastic items and can break easily.

Followed a video, pretty straightforward. Be sure to clean all the area. My husband used cotton swabs to clean all the gunk.

Remove two screws at top that fasten dishwasher to cabinet. Slide dishwasher out to expose the two links that attach the door to the springs. Fit the new links to the springs and door.

change out the old pump with new one actually quieter running pump awesome

Took less than one minute

New latch assembly improved door closure. However, door latch did not solve problem. There appears to be another problem.

Installation was very easy. The online video was excellent and clear.
Thanks

Ordered the "right" part according to the diagram. The part I received was about 1/4" too long so I couldn't use the whole manifold. Took the rubber end off and - fortunately- it fit the old manifold. Dishwasher works fine now. Wish I could have ordered just the rubber valves.