WDF530PSYB3 Whirlpool Dishwasher - Instructions

Did the repair, but needed one extra step not described in video:

I followed the directions on the PartSelect Youtube video - very helpful! I do believe the heating element was the original culprit, as it had a "burn" area about the size of a dime that caused it to almost break into two parts. Obviously a point of failure.

BUT - after replacement, it still did not solve the problem of the dishes not drying.

After much web searching, I tried the diagnostic mode on the dishwasher, and that did a hard reset of the logic board and FIXED the problem.

So in all, it required both a new heating element AND a hard reset via diagnostic mode.

Followed the easy how-to video from PS. It was as easy as changing a light bulb.

I ordered the cap for my kitchen aid dishwasher and it is too small.

thought it could be due to the overfill control switch,so ordered one and replaced one in the washer. However, it did not solve the problem. Having a repair company coming to look at the dishwasher. Tipped the washer on its back and switch was readily accessable. Only had to open plastic covering over the switch, disconnect the wires and install new switch and reconnect the wires.

Something had been loaded in the dishwasher that had gone thru the basket - it hit the arm sprayer and broke it off.

Replacement sprayer was exactly the same - the partselect website has very specific identification method so you get the proper part. You must have your model number.

I watched a you tube video which was referred by part select. This was helpful.

I did not realize at first that only part of the arm sprayer had broken off. The arm sprayer broke off, but there is a base to the arm sprayer that was still attached to the dishwasher. So I could not, of course , fit the new arm with its base over the existing base because they are the same size. Once I realized this, it was a simple replacement, following the youtube instructions. You do have to press and turn counter clockwise to get the old base off, but once that was done, the new sprayer arm, which arrived attached to the base, easily fit, and press hard to turn it clockwise to reattach it..

It has worked perfectly. It is a hard turn to get the arm sprayer off or on, which is good so it doesn't come loose during washing, but when replacing it, you aren't sure of why it won't turn. It is a hard turn. Watch the you tube video.

Looked on you-tube and it was so easy. Pump on bottom right. unplug pump and do a halfway turn. Plug the new one up and place the pump on, and turn halfway and its on. START your dishwasher

Only one friction sleeve was broken. So I pulled out the dishwasher to see how the one on the other side went on. It was very easy to replace and I replaced both. Unit works fine now.

This is the second time I have replaced a rack. You just pop on the new rollers and you're good to go!

Disconnected the damaged hose extension from the dishwasher outlet drain hose and the connection to the sink drain. Removed two clamps. One a spring clamp and the other a screw clamps. Connected the new extension hose with a spring clamp to the dishwasher outlet drain hose. Connected the other end to the sink drain with a screw clamp. Checked for leaks. Good to go!

Screwed in new cap

After replacing the door seal and the dishwasher still leaked a lot of water out the bottom of the door, I read posts by a couple of other DIY who said the lower spray arm can split at the seam and cause this. One post noted it is very difficult to determine if this is the problem, that you may have to take the blade of a screwdriver and try to pry the seam apart gently to see if a gap does appear with very little force being applied. If so, then just imagine what happens when that very hot water makes that plastic more flexible and then the seam opens and forces waves of water against the lower door. I could see a small seam split using that strategy and when I replaced the spray arm, my leak stopped. I don't regret replacing the door seal as it had a couple of small tears and hard water deposits all over it, so it was time to do that even though it was not the culprit for the extensive leak. The arm is SO EASY to replace, just twist the plastic nut under it and it pops right off. Put the new one on and twist the nut the other way and it secures it.

Put in both a new element and thermostat. Did not fix problem. Using an ohm meter I did not measure any voltage to the thermostat. Suspect it’s a problem in the control unit, and decided to replace dishwasher.

Follow the u tube instruction. Replacing the pump was very simple and easy. The hard part was getting the dishwasher out of the cabinet and back in again.

Thanks to everyone for posting their experiences on changing the heater element. The most difficult part of the repair was getting the dishwasher out of the cabinet. I didn't know that I should disconnect the water line underneath the sink and this would make the removal easier. Also, because the copper water line going to the dishwasher was kinked, I ended up changing it with a flexible steel braided line.....much easier to install.

Once the dishwasher was out of the cabinet, I turned it over and easily removed the clips that held the heater element in.

I would definetly recommend people doing this repair themselves, it will save you a lot of money!!!!!

Exact fit and at my door in two days