BLB14BRANA0 Whirlpool Dishwasher - Instructions

Shut the power to the dishwasher off. Pulled unit out from under the counter top and raised the left hand side up for easy access. Disconnected the wiring, undid the clips, turned counter clockwise and removed. Reversed the order for installation and Connected the power. Ran several cycles successfully. Problem fixed. Burnt out water pump. Good as new if not better so far. Easy item search, Fast Shipping, Quality Part, Fair Pricing. Thank You Partselect.com

I pulled the rack and removed failed parts, then reassembled. I would note that the videos are helpful as dishwasher racks can be a bit of a puzzle.

Why manufacturers use so much plastic in a heated environment is beyond me. The heat cycle degrades the plastic to failure - poor design!

The upper spinner was laying in the top washer basket. I went online but no help was avaiable. Went to store where we purchased dishwasher and they gave me part number to order but not online I had to call to order. Part arrived in about three days. I took two screws loose on the top of dishwasher removed broke retainer to put new retainer in but I drop it into dishwasher so you have to me very careful
so I tried to order just the retainer but is not sold by it self. Had to order whole new kit. Other than that it is easy dishwasher runs like a new one.

I removed the old gasket. Cleaned the surface under the old gasket and began pressing the new gasket into place. Make sure the gasket is pressed all the way in to properly seat it in the groove. Didn't use the tube of gasket sealer and it worked perfectly no leak,

Was a cinch just watched the video whole procedure took an hr or so

Make sure you have everything you need before you start. The upper rack adjuster broke when the left track failed and needed to be replaced. Although only the left side track failed, the right side would have soon enough.

This repair was fairly simple. First, toggle the circuit breaker off and turn off the water supply under the sink. Remove gray plastic covers to expose and remove Phillips head screws on each side of inner door frame then remove plastic kick plate before sliding the dishwasher out roughly 20”. The insulation needs to be folded back (tab release back bottom corner) to expose the four rack fasteners on each side. A small socket bit (I used a slow speed hand drill) makes quick work of removing old tracks but make sure one hand is inside on the track to catch what’s left of it. Replace both tracks (the second will fail) arrow pointing up using the fasteners you removed. Reset the insulation and make sure water, drain and electrical connectors are all in good order before sliding dishwasher back and fastening side frame screws to adjoining cabinets (tip: use painter’s tape or similar to keep screw head connected to screwdriver). Replace plastic caps and the kick plate. I had to replace the upper rack adjuster before reinstalling the upper rack on the new tracks. Check the bottom filter and reservoir for any plastic bits or ball bearings and remove them before turning power and water back on. Enjoy not having to hand wash dishes again. For me, about 40 minutes.

1.Check the lines for any obstruction. Gunk can easily build up. I have used the dishwasher for approx. 10 years. I do rinse/scrap dishes prior to loading.
2. Drain all remaining water.
3. Unplug the dishwasher.
4. Grab a towel and proper screw driver. Unscrew the bottom protective plate. Remove the insulation plate.
5. The drain pump is located to the bottom left. Have your towel under it. Unplug it gently. Turn counter clockwise to remove.
6. Install the new drain pump (reverse order)
7. Return the insulation plate. Screw back the bottom protective plate.
8. Plug in

I found instructions on line when I goggled my dishwasher name and model number with the words noisy door. There were three or four good suggestions at a couple of the sites I visited. I tried applying vasoline, then silicone to the rope where it travels through the plastic guides but that just cut the sound down about 50%. My dishwasher has plastic guides that look like rollers but they don't turn, they are fixed in place. The ropes squeak as the pass over the guides. The replacement part kit has plastic guides that turn like wheels now so the rope does not drag over them and squeak. This repair could be done by me in 20 minutes or less every time now that I know what I am doing.

I removed the black bottom metal cover then turned the nuts on the adjusting (leveling) bolts to lower the front end of the dishwasher so I could pull it out of the cabinet. Once I lowered is as low as it would go I opened the door and pushed down on it which tilts the dishwasher down and you pull out on it and the top lip clears the cabinet. If your dishwasher just pulls out the first time you try these steps may not be necessary.
Once the dishwasher is out the guides and rope are down at the bottom in the front by the door. It's obvious what to do to replace them.

The repair was really easy. First disconnected electricity staring with fuses and removing wires from dishwasher, then disconnected drain hose and water hose. Pulled it out and removed pump turning clockwise no need for tools and same way installed new one. Very easy

followed video instruction

This was tricky, not so much the difficulty of the repair so much as finding the right instructions. There weren’t any on your website. YouTube videos were all over the place in terms of specific set ups. Eventually I found the right one. This would have been very easy and would have taken less than 15 minutes if I had the right instructions from the start. Most of my time was taken with searching for instructions.

Very easy to repair with the replacement wheel assembly. Popped out the broken one, popped in the new one. Price was nothing compared to having an professional repair person come to the home. Glad I found you on line!

My husband called Part Select and described the problem. After we sent a couple of photos to the technician, she determined the part that we needed...a top rack assembly unit...and it arrived within a few days.
I watched the video that Part Select provided and it made the job so much easier than if the new part had been sent with a booklet of diagrams and written instructions. The video showed exactly how to dismantle the old part and then install the new part. It was also helpful to compare the part I was working with to the same part on the other side of the rack so that I knew for sure that I had it positioned correctly.
The part and shipping cost about $70. It would have cost more than 3 times as much if I had to call a repairman.

removed old gasket, installed new.
No Leaks!!
Saved the cost of a new dishwashers

I watched the YouTube video I found in the link provided but PartSelect and followed the steps shown in the video. I replaced the two broken rack adjusters in about 20 minutes. I especially like the fact that PartSelect helped with the link provided in the email that acknowledged the part order. A great customer service. I’ve passed this fact on to my other friends who routinely DIY repair projects.