ADB1400PYB2 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Diane from LAKE GEORGE, NY
- Parts Used:
- WP8565925
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
I needed to add a clip stop to the right front track.
I manually attached the track stop to the right track in the disheasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carole from IRVINE, CA
- Parts Used:
- WP8565925
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Roller wheel broke off upper rack and also end rack stops needed replacing.
Husband watched your repair video. Everything went well and we are very pleased.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rich from boulder city, NV
- Parts Used:
- W10518394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
heater showing signs that it was going to fail soon
removed unit from cabinet disconnected water and drain lines replaced heater very easy to do it took more time to remove unit from under counter than replace heater piece of cake..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dawn from MELBOURNE BCH, FL
- Parts Used:
- WP8565925
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
Top rack broke
I had to replace the whole sliding system on the top rack. Plus the clips holding it. It snapped. I watched the video and did the steps from Steve. The rack slides better than when brand new. Whirlpool wouldn’t pick up phone but part select did. So thank you for being there so I could fix the rack and be able to use the dishwasher again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Arlington, MA
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Top rack of dishwasher kept pulling all the way out
Our dishwasher's top rack would pull too far out which made it hard to stay in alignment. It had lost it's track stop. I easily ordered the part from PartSelect, and it came more quickly than I expected; I clicked it in place and it runs like new. It's wonderful to deal with a company that knows the frustration of not having your appliance in good working orfer.
Thank you.
Sue M
Masdsachusetts
Thank you.
Sue M
Masdsachusetts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from RIVERSIDE, IL
- Parts Used:
- W11175771
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
The Inlet Valve cracked from the severe cold weather we had in Chicago area.
Removing and installing the new part was fairly simple. We removed the water hose first since it is the easiest to see. We then removed the screw holding the part to the metal frame. We slid out the part out of the holder to remove the black hose and electric plug (it is like the old phone jacks). After it was completely off we plugged in the electric to the new part which was very easy since it can only go in one way. We slid the new part in place and attached the black hose. We attached the piece to the frame with the one screw and last we attached the gold (garden hose) connection. We turned on the water to look for any leaks then turned the power on and ran it through a partial rinse to be sure there were no leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from ROLLA, MO
- Parts Used:
- WP8269145
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
installer from lowes di not do it right, forgot to put scew in, instead he used shims, as usuall no more installs from Lowes
followed directions, a kid could have done it,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- T.w. from Batesville, AR
- Parts Used:
- W10518394
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
heater element burnt in two
1. Open dishwasher door, to access the screws holding dishwasher to cabinet.... remove these screws.
2. May need to shut water off and unscrew water line and waste line (if they aren't long enough because you will need to pull dishwasher out.
3. Unplug electricity
4. Pull dishwasher all the way out... probably need to disconnect the water and waste lines
5. crescent wrench to unscrew the plastic screws in back
6. Disconnect two wires going to element
7. Replace element... reverse steps
8. Not too bad at all
9. Part Select is Awesome !!!!
2. May need to shut water off and unscrew water line and waste line (if they aren't long enough because you will need to pull dishwasher out.
3. Unplug electricity
4. Pull dishwasher all the way out... probably need to disconnect the water and waste lines
5. crescent wrench to unscrew the plastic screws in back
6. Disconnect two wires going to element
7. Replace element... reverse steps
8. Not too bad at all
9. Part Select is Awesome !!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Felix from MELBOURNE, FL
- Parts Used:
- WP8565925
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Timer repairs
Well, it’s very easy to repair. But, what I like if ur Company is, the availability, of the parts.
Thanks you.
Thanks you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from BOULDER, CO
- Parts Used:
- W10518394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Dishwasher was not drying the dishes.
I followed installation instructions from this site and all went well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- al from Fuquay Varina, NC
- Parts Used:
- WP8565925
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
Dishwasher circulation pump malfunction
Tipped over washer, removed attachment bolts, installed new pump by clamping water hoses. Be sure to use proper crimping pliers, not the generic slip joint pliers. Replacement pump included required new clamps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from St. Joseph, MO
- Parts Used:
- WP8524471
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Latch broke
I saves the old part to see how it was to be installed. It was very easy. I saved the $50 + dollars for a SERVICE CALL.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SAMUEL W from SARASOTA, FL
- Parts Used:
- W11768590
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Leak around door
Pulled out old gasket, pressed in new starting middle top. No more leak.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JoAnn from EAST WINDSOR, NJ
- Parts Used:
- WP8268645
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Wheel assembly was cracked
I just snapped the old one off and snapped the new one on..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from HUNTINGTON, WV
- Parts Used:
- W11133712
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Pump quit working
Removed the old pump, got part number from it, ordered the part. Simply a matter of slipping the new pump into place, reconnecting the electric, testing the machine out to make sure it did not leak. Then slid back in place with the cabinets.
Was this instruction helpful to you?
Thank you for voting!