WDF510PAYW2 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gary from WAUKEE, IA
- Parts Used:
- WP8268961
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Friction sleeve came apart ....would not hold door in place
Pull dishwasher out a few inches. Disconnect spring from plastic connector with long nose pliers. Remove connector. Replace friction sleeve. Replace connector.Reconnect spring to plastic connector. This completes repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Wichita, KS
- Parts Used:
- W11752368
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Upper dishrack needed replaced
I removed the upper dishrack easily by removing the end clips and sliding the tray out. Removal of the revolving sprayer was easy as it just clipped on to the bottom of the rack. The rack was not the rack that was ordered and I was informed that this was the correct rack for the dishwasher even though the description and picture was different that what I received. There were no instructions with the rack to explain how to attach the "flaps" that can go over lightweight dishes to keep them from flipping. Every way I tried to attach the flaps did not work. When I was able to attach one it would pop off if I raised the flap to place a dish underneath it. I finally gave up on the flaps and reinserted the rack onto the rails and put the end clips back in place. The rack works fine other than it is not the one that was described and was not the rack that I wanted.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from BATON ROUGE, LA
- Parts Used:
- WP8268961
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher door drops quickly to wide open position when unlatched
Rubber friction sleeves on each side of the door provide resistance to prevent the door from quickly opening when unlatched. Over time the friction sleeve may crack and fail. Two friction sleeves are required for repair. Install a new sleeve on each side of the dishwasher door near the spring connector at the bottom.
Open dishwasher door.
Remove the screw from the left and right bracket at top of dishwasher door opening. Brackets secure the dishwasher to the countertop.
Gently pull the dishwasher forward to expose the door spring on each side of door at bottom.
Unhook the plastic spring connector from the left door spring hook by pulling the connector slightly forward and lifting from the door spring hook. Remove the old friction sleeve if still in place by sliding over the door connection hook. Discard the old sleeve.
Insert the new friction sleeve over the door spring connector hook and push until the friction sleeve is in position completely past the spring hook. Reconnect the plastic spring connector to the door hook.
Repeat for right side of door.
Close and latch the dishwasher door. Unlatch the door. The door should remain in the nearly closed position held in place by the friction sleeves.
Slide the dishwasher back to the original position under the counter top.
Insert the screws in the top brackets to secure the dishwasher.
Open dishwasher door.
Remove the screw from the left and right bracket at top of dishwasher door opening. Brackets secure the dishwasher to the countertop.
Gently pull the dishwasher forward to expose the door spring on each side of door at bottom.
Unhook the plastic spring connector from the left door spring hook by pulling the connector slightly forward and lifting from the door spring hook. Remove the old friction sleeve if still in place by sliding over the door connection hook. Discard the old sleeve.
Insert the new friction sleeve over the door spring connector hook and push until the friction sleeve is in position completely past the spring hook. Reconnect the plastic spring connector to the door hook.
Repeat for right side of door.
Close and latch the dishwasher door. Unlatch the door. The door should remain in the nearly closed position held in place by the friction sleeves.
Slide the dishwasher back to the original position under the counter top.
Insert the screws in the top brackets to secure the dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from SAN DIEGO, CA
- Parts Used:
- WPW10224428
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Detergent lid failed to stay closed
Watched your online video,and the rest was simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from HIGHLAND, NY
- Parts Used:
- WPW10317197
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Arm did not turn!
Removed old arm and put knew one on!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from GLADSTONE, MO
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Front Track stop missing
Snap new track stop into place. Took a few minutes to figure out top/bottom and inside/outside, but no issues
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from PEMBROKE PNES, FL
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Top rail stop clip broke
Very easy to remove the broken one and just clip in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KATHLEEN from LINDENHURST, NY
- Parts Used:
- WP8558307
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old cap had fallen out and partially melted
Unscrewed the old cap, replaced with the new one. It couldn't be easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from LAMAR, IN
- Parts Used:
- W10542314
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
water leaking on bottom left of door
Just pulled the old gasket off and started on the bottom of both sides of the door installing the new gasket and finished at the top in the middle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from BEDFORD, MA
- Parts Used:
- WP8558307
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The wife didn't screw it in far enough and it fell down on the heater and melted
I inserted the new one and turned it clockwise.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from VAN BUREN TWP, MI
- Parts Used:
- 4317824
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
none
removed and installed cords with screw driver
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from KNOXVILLE, TN
- Parts Used:
- W10542314
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Door leaks a lot
Followed the video. It works perfectly. Used a small paint scraper to remove stubborn scale where gasket seats. Used steel wool on door to assist in removal of rough scale.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from POWDER SPGS, GA
- Parts Used:
- WPW10503548, W10827631
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replace black access panel on Whirlpool dishwasher (model WDF520PADM7)
I needed to replace the black access panel on my Whirlpool dishwasher (model WDF520PADM7).
By following the instructions in this short video (https://www.youtube.com/watch?v=995mtdO7rQg) , I was able to complete the replacement in under 10 minutes. You'll need a flat-blade screwdriver. The Retainer Clip - Black can be a little tricky to position into the opening, so have patience.
Keep in mind that the Retainer Clip - Black only contains ONE clip and so you must make sure to order TWO Retainer Clip - Black from PartSelect.
By following the instructions in this short video (https://www.youtube.com/watch?v=995mtdO7rQg) , I was able to complete the replacement in under 10 minutes. You'll need a flat-blade screwdriver. The Retainer Clip - Black can be a little tricky to position into the opening, so have patience.
Keep in mind that the Retainer Clip - Black only contains ONE clip and so you must make sure to order TWO Retainer Clip - Black from PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from KLAMATH FALLS, OR
- Parts Used:
- WPW10317197
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Upper spray for bottom rack, broken
Upper jet part for top rack, directly beneath it....it has nubs meant to slide in grooves for the replacement. Waited a week for the new part, once arrived, I slipped the piece in place as nubs for my guide, and it snapped in pkace.
Easy fix.
Easy fix.
Was this instruction helpful to you?
Thank you for voting!