WDF510PAYB2 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mary Ann from DEFIANCE, MO
- Parts Used:
- WPW10224428
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Replace the soap dispenser
It is VERY IMPORTANT that you watch the HOW TO VIDEO provided from the BEGINNING, then it will be VERY EASY to do. I took out ALL the screws, I DIDN'T need to do, so it took longer, & made things more difficult.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from SAN DIEGO, CA
- Parts Used:
- WPW10224428
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Detergent lid failed to stay closed
Watched your online video,and the rest was simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Wichita, KS
- Parts Used:
- W11752368
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Upper dishrack needed replaced
I removed the upper dishrack easily by removing the end clips and sliding the tray out. Removal of the revolving sprayer was easy as it just clipped on to the bottom of the rack. The rack was not the rack that was ordered and I was informed that this was the correct rack for the dishwasher even though the description and picture was different that what I received. There were no instructions with the rack to explain how to attach the "flaps" that can go over lightweight dishes to keep them from flipping. Every way I tried to attach the flaps did not work. When I was able to attach one it would pop off if I raised the flap to place a dish underneath it. I finally gave up on the flaps and reinserted the rack onto the rails and put the end clips back in place. The rack works fine other than it is not the one that was described and was not the rack that I wanted.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from BATON ROUGE, LA
- Parts Used:
- WP8268961
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher door drops quickly to wide open position when unlatched
Rubber friction sleeves on each side of the door provide resistance to prevent the door from quickly opening when unlatched. Over time the friction sleeve may crack and fail. Two friction sleeves are required for repair. Install a new sleeve on each side of the dishwasher door near the spring connector at the bottom.
Open dishwasher door.
Remove the screw from the left and right bracket at top of dishwasher door opening. Brackets secure the dishwasher to the countertop.
Gently pull the dishwasher forward to expose the door spring on each side of door at bottom.
Unhook the plastic spring connector from the left door spring hook by pulling the connector slightly forward and lifting from the door spring hook. Remove the old friction sleeve if still in place by sliding over the door connection hook. Discard the old sleeve.
Insert the new friction sleeve over the door spring connector hook and push until the friction sleeve is in position completely past the spring hook. Reconnect the plastic spring connector to the door hook.
Repeat for right side of door.
Close and latch the dishwasher door. Unlatch the door. The door should remain in the nearly closed position held in place by the friction sleeves.
Slide the dishwasher back to the original position under the counter top.
Insert the screws in the top brackets to secure the dishwasher.
Open dishwasher door.
Remove the screw from the left and right bracket at top of dishwasher door opening. Brackets secure the dishwasher to the countertop.
Gently pull the dishwasher forward to expose the door spring on each side of door at bottom.
Unhook the plastic spring connector from the left door spring hook by pulling the connector slightly forward and lifting from the door spring hook. Remove the old friction sleeve if still in place by sliding over the door connection hook. Discard the old sleeve.
Insert the new friction sleeve over the door spring connector hook and push until the friction sleeve is in position completely past the spring hook. Reconnect the plastic spring connector to the door hook.
Repeat for right side of door.
Close and latch the dishwasher door. Unlatch the door. The door should remain in the nearly closed position held in place by the friction sleeves.
Slide the dishwasher back to the original position under the counter top.
Insert the screws in the top brackets to secure the dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from HIGHLAND, NY
- Parts Used:
- WPW10317197
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Arm did not turn!
Removed old arm and put knew one on!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KATHLEEN from LINDENHURST, NY
- Parts Used:
- WP8558307
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old cap had fallen out and partially melted
Unscrewed the old cap, replaced with the new one. It couldn't be easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from MILLBURY, MA
- Parts Used:
- W11175771
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Dishwasher wasn’t getting water.
I located the water inlet valve underneath. After moving the dishwasher out from the cabinet, I tilted it . Then I disconnected the black hose with the pliers . Using the adjustable wrench I unscrewed the water feed to the valve . I then unscrewed the valve from the frame and disconnected the wire plug by unlocking and slipping it away from the valve. To install I did all this in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from BEDFORD, MA
- Parts Used:
- WP8558307
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The wife didn't screw it in far enough and it fell down on the heater and melted
I inserted the new one and turned it clockwise.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from GLADSTONE, MO
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Front Track stop missing
Snap new track stop into place. Took a few minutes to figure out top/bottom and inside/outside, but no issues
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobby from Temperance, MI
- Parts Used:
- W10542314
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replaced Door Gasket.
Fast,smooth,easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from VAN BUREN TWP, MI
- Parts Used:
- 4317824
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
none
removed and installed cords with screw driver
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from LAMAR, IN
- Parts Used:
- W10542314
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
water leaking on bottom left of door
Just pulled the old gasket off and started on the bottom of both sides of the door installing the new gasket and finished at the top in the middle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- thomas from SCHENECTADY, NY
- Parts Used:
- W10542314
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
leaking water out of lower left corner of dishwasher door
removed old door gasket, cleaned gasket groove, and than started new gasket in both corners working my way to middle top of door, made sure gasket was in groove properly w/my fingers. problem solved
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from DOWNS, KS
- Parts Used:
- 4317824
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Someone had used the wrong type of power cord
Recently bought a whirlpool dishwasher, the dishwasher was converted to a portable dishwasher and they did not use the cord application power cord so they machine was blowing our breaker, instructions were very simple and installation was easy!
Was this instruction helpful to you?
Thank you for voting!