Models > WDF530PAYB3 > Instructions

WDF530PAYB3 Whirlpool Dishwasher - Instructions

Jump to:

All Instructions for the WDF530PAYB3
91 - 105 of 386
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Frances from Longmeadow, MA
Parts Used:
W10542314
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
worn gasket was fraying at bottom of door, leaking
just pulled old gasket out. New gasket took 2 attempts to fit in properly, but simple to do. Very easy to press into groove. Fit like a glove! Website drawings made choosing part very easy, thanks
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from WESTERVILLE, OH
Parts Used:
WP8565925
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Rollers broke off top rack assembly
Replacement parts from factory installed using u tube support video


Also replaced stop ends for top rack by removing old clip in to push down and lined up to secure in slots at end of rack, notice new plastic parts are installed by pushing hardware into slots downward until they clip into place
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Cameron from DEFIANCE, OH
Parts Used:
WPW10491331
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Lower spray arm had a small seam split forcing waves of water against the lower door causing water to leak out the door bottom.
After replacing the door seal and the dishwasher still leaked a lot of water out the bottom of the door, I read posts by a couple of other DIY who said the lower spray arm can split at the seam and cause this. One post noted it is very difficult to determine if this is the problem, that you may have to take the blade of a screwdriver and try to pry the seam apart gently to see if a gap does appear with very little force being applied. If so, then just imagine what happens when that very hot water makes that plastic more flexible and then the seam opens and forces waves of water against the lower door. I could see a small seam split using that strategy and when I replaced the spray arm, my leak stopped. I don't regret replacing the door seal as it had a couple of small tears and hard water deposits all over it, so it was time to do that even though it was not the culprit for the extensive leak. The arm is SO EASY to replace, just twist the plastic nut under it and it pops right off. Put the new one on and twist the nut the other way and it secures it.
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lynn from Schenectady, NY
Parts Used:
W10311986
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Old rack rusting
This is the second time I have replaced a rack. You just pop on the new rollers and you're good to go!
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Juan Carlos from WATAUGA, TX
Parts Used:
WP8565925, WPW10498900
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Part snap broken
Snap in the missing track stop and twist snap the middle spray arm. That simple.
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from NEW HOPE, PA
Parts Used:
8269144A
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers, Wrench (Adjustable)
A mouse was chewed through the hose and ate part of it. Di
Disconnected the damaged hose extension from the dishwasher outlet drain hose and the connection to the sink drain. Removed two clamps. One a spring clamp and the other a screw clamps. Connected the new extension hose with a spring clamp to the dishwasher outlet drain hose. Connected the other end to the sink drain with a screw clamp. Checked for leaks. Good to go!
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Chris from VALLEY STREAM, NY
Parts Used:
WP8268961
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
Door was falling down quickly
Only one friction sleeve was broken. So I pulled out the dishwasher to see how the one on the other side went on. It was very easy to replace and I replaced both. Unit works fine now.
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jim from NEW CARLISLE, IN
Parts Used:
WP8558307
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Cap had loosened and fell onto heater coil and melted.
Screwed in new cap
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Thomas from SEATTLE, WA
Parts Used:
WP661566
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Heating element not heating for both wash and dry.
Put in both a new element and thermostat. Did not fix problem. Using an ohm meter I did not measure any voltage to the thermostat. Suspect it’s a problem in the control unit, and decided to replace dishwasher.
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gene from SKYKOMISH, WA
Parts Used:
WPW10348269
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
dishwasher would not drain
Follow the u tube instruction. Replacing the pump was very simple and easy. The hard part was getting the dishwasher out of the cabinet and back in again.
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Aaron from Aurora, IL
Parts Used:
W10518394
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Wrench (Adjustable)
Start light was flashing
Thanks to everyone for posting their experiences on changing the heater element. The most difficult part of the repair was getting the dishwasher out of the cabinet. I didn't know that I should disconnect the water line underneath the sink and this would make the removal easier. Also, because the copper water line going to the dishwasher was kinked, I ended up changing it with a flexible steel braided line.....much easier to install.

Once the dishwasher was out of the cabinet, I turned it over and easily removed the clips that held the heater element in.

I would definetly recommend people doing this repair themselves, it will save you a lot of money!!!!!
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
rick from sparta, NJ
Parts Used:
W10542314
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Dishwasher leaked occasionally due to age and condition of old gasket
Repair was a "no brainer". Pulled out the old gasket, started the replacement of the new gasket in the lower right hand corner and worked all the way around the opening, then trimmed excess gasket of about 2" with a pair of scissors and I was done. Total time - less than 5 minutes.
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Leslie from LANCASTER, PA
Parts Used:
W10827631
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Took off kick plate to get ready for winter shut down
Put the kick plate under the dishwasher and screwed it in. Easy!
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ed from Schofield, WI
Parts Used:
W10311986
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
The bottom dishrack was having areas that were breaking off and showing rust.
We took the rollers off the old one (new ones came with the dishrack also) and put them on the dishrack (they snapped on). There was also an extra piece that we figured out how to put on. Then slid it in place and it was fine.
6 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Todd from ROTONDA WEST, FL
Parts Used:
WPW10503549
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
A plastic retainer pin for the bottom kick panel was missing.
simply line up the new pin with the rectangular slot in the kick panel and metal panel behind, slide the pin in and turn it with a flat blade screw driver.
NOTE: the original pin was black. A black replacement part cost $29 plus shipping! A knock-off pin was only $6 plus shipping. I got the cheap one and colored it with a black Sharpee marker before installation.
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WDF530PAYB3
91 - 105 of 386