WDF780SLYW2 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from SAINT CHARLES, MO
- Parts Used:
- W10872845
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
New filter
Ordering the part was very easy. It shipped fast and delivered over 3 days. It fit perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from INDIANOLA, IA
- Parts Used:
- WPW10498900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
replace middle spray arm and water srayer
remove 2 locks on metal roller guides. remove top basket. turn upside down on counter.remove spray arm by pryng one side in and lift out then push other side down and the out. install same as removal. line spray arm and turn clockwise til you hear a click.install basket and install locking plugs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from ALTADENA, CA
- Parts Used:
- WPW10491331
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
After cleaning the filter basket & metal grill (floor of dishwasher), I neglected to secure the bottom spray arm. It came loose, landed on the heating coil, and melted.
I simply removed the melted spray arm, then set the new spray arm in place, twisted the built-in securing nut (clockwise to its stop), and it worked without any problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Milwaukee, WI
- Parts Used:
- WPW10195622
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
rack stop needed to be replaced
took out the top dishwasher rack. Pulled out the track needing repair. used a flat screwdriver to pry off the defective stop. Slid the track (without the stop) back over the rollers. Snapped in the new track stop and that was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from NAUGATUCK, CT
- Parts Used:
- W11177741
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
water leak during wash cycle
I followed the video on the site and it worked perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- philip from racine, WI
- Parts Used:
- W10195416
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
replaced lower rack wheel assembly
watched video took less than 5 min to replace veeeery easy to do
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from KINGWOOD, TX
- Parts Used:
- W11177741
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Slow water drip on bottom side of door, both sides.
Pulled off old seal. Pressed into groove the new door seal. No parts required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from CHAPEL HILL, TN
- Parts Used:
- W11177741
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Leaking around door
Pulled off old seal found center of new seal and pushed new seal into channel that old seal came out of starting at top middle underneath the latch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois from HUDSON, NC
- Parts Used:
- WPW10348269
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
pump not working
Looked on you-tube and it was so easy. Pump on bottom right. unplug pump and do a halfway turn. Plug the new one up and place the pump on, and turn halfway and its on. START your dishwasher
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from AUBURNDALE, WI
- Parts Used:
- WPW10195039
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
water fill overflows at times
thought it could be due to the overfill control switch,so ordered one and replaced one in the washer. However, it did not solve the problem. Having a repair company coming to look at the dishwasher. Tipped the washer on its back and switch was readily accessable. Only had to open plastic covering over the switch, disconnect the wires and install new switch and reconnect the wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from ELGIN, IL
- Parts Used:
- W10864081
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Leaking door seal
Pulled dishwasher out from under the counter, removed faulty seal, installed new seal. Easy to understand directions are on web site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Briant from Byron, MN
- Parts Used:
- 4317824
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
There was no problem
I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Miami, FL
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Factory crimped end of link cord pulled out of plastic fastner that hooks on door.
Removed 2 screws that fasten dishwasher to underside of countertop. Pulled dishwasher out from under the countertop for access to sides. Hooked link on door, threaded cord around 2 wheels, hooked spring to back of dishwasher, stretched spring and hooked to eye on end of link cord. I found it very difficult to hook spring to link then try and stretch spring to hole at back of dishwasher. Easier to pull spring and link towards each other and connect. Note: This link was actually different from the original. The plastic end that connects to the door actually hits the first wheel when door is closed but it doesn't seem to prevent the door from locking properly (old design was better). However, I shaved this plastic end to provide better clearance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from FORT MYERS, FL
- Parts Used:
- WPW10348269
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Dishwasher would not drain properly due to broken impeller in the pump. Could hear and feel vibration thru pump body.
Followed the easy how-to video from PS. It was as easy as changing a light bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brad from ABILENE, TX
- Parts Used:
- W10537869
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
The diverter motor was leaking
Actually, I found a video on Youtube with excellent instructions once you got past the really simple stuff like disconnecting power and water and drain.
I would recommend just finding a fairly similar model on Youtube and follow their directions. It was really easy.
I would recommend just finding a fairly similar model on Youtube and follow their directions. It was really easy.
Was this instruction helpful to you?
Thank you for voting!