GU3200XTXB0 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Charlene from Lafayette, LA
- Parts Used:
- W10083957
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
poor cleaning
removed both upper and lower racks. removed lower spray arm(left hand thread) removed "water delivry tube and upper spray arm. removed torx screws on pump cover. removed inner chopper cover. Chopper assy had come apart and was full of food crud. cleaned out and installed new chopper assy. kind of tricky don't force it. reassembled. tested OK.could tell sound of more forceful water pressure
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Ridgecrest, CA
- Parts Used:
- W10258275
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Wirlpool Dishwasher not getting power to panel. Outlet checked out fine
First I unplugged the dishwasher.Then I removed 6 Torx screws, popped off cover, cut wires to old fuse, stripped wire, placed wires in new part, tightened screws, reassembled in reverse order, plugged unit back in and tested. WOO HOO!
I saved over $150.00 by doing it myself instead of having a repairman come out! That's 4 free fishing trips!
I saved over $150.00 by doing it myself instead of having a repairman come out! That's 4 free fishing trips!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- W. C. from San Rafael, CA
- Parts Used:
- WPW10199696
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
Broken catch on soap dispenser door
1. Removed six screws securing outer panel to dishwasher door.
2. Removed outer panel which exposed back of dispenser.
3. Remover six screws holding dispenser.
4. Removed dispenser.
5. Installed new dispenser.
6. Replaced six screws.
7. Reattached electrical connection to dispenser relay.
8. Reinstalled outer panel with six screws.
2. Removed outer panel which exposed back of dispenser.
3. Remover six screws holding dispenser.
4. Removed dispenser.
5. Installed new dispenser.
6. Replaced six screws.
7. Reattached electrical connection to dispenser relay.
8. Reinstalled outer panel with six screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Olivenhain, CA
- Parts Used:
- WPW10199696
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
The latch to the soap dispenser appeared to break. The latch was found on the floor.
After I took apart the inside of the door, removing 12 star screws, I was able to see the inside of the automatic soap dispenser device. Since I now had the new device to look at, I was able to replace the latch pin back in the existing device and it worked!
I now have a replacement if the device actually breaks in the future and looking at the small plastic pieces, it will probably happen sooner or later.
I now have a replacement if the device actually breaks in the future and looking at the small plastic pieces, it will probably happen sooner or later.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLIAM from FERNANDINA, FL
- Parts Used:
- W10258275
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher would not run
Removed the Bi-Metal fuse and ordered a new one and recerved it two days after ordering. Replaced it and it worked.
Was this instruction helpful to you?
Thank you for voting!
spray arm did n't move because it had a crack in the end
First I had to remove the upper dish rack from the dishwasher. This was the most difficult part of the entire fix. I found the screw which holds the spray arm in place, Removed it and took off the old spray arm. Then I replaced the seal and put the entire thing back together, put the screw back in and replaced the rack. Then I ran a load of dishes and discovered the machine works just fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ellen from Park City, UT
- Parts Used:
- WPW10082892
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher heater broken
I ordered this part after the sanitized light on my dishwasher was flashing. The dishes were no longer drying. To replace the part, my husband pulled out the dishwasher and unscrewed some nuts (accessing under the heater through the side openings). The entire repair took under 15 minutes, and works perfectly. I have to mention that the heater was shaped differently than the one it replaced, but was a perfect fit in the clips.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerome from Greensburg, IN
- Parts Used:
- 8193951A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
The ceramic seal had failed, allowing water to destroy the front motor bearing.
Removed dishwasher from under the counter and took it to my shop. With the washer on its side, I removed the motor, then the impeller and seal. I then disassembled the motor and replaced the front bearing(purchased separately). This required an arbor press. I then reassembled the motor and installed the new seal and impeller. Reassembled in reverse order. Reinstalled under the counter and made conections. Checked for leaks and proper operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from Moreno Valley, CA
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken Door Links
Remove two screws at top that fasten dishwasher to cabinet. Slide dishwasher out to expose the two links that attach the door to the springs. Fit the new links to the springs and door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from Wethersfield, CT
- Parts Used:
- W11196317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Seal on dishwasher worn out and coming loose.
Removed old seal, cleaned track, applied adhesive for new seal, seated new seal in track, closed door for 24 hours to allow adhesive to cure, then used dishwasher without difficulty. An easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from Smyrna, TN
- Parts Used:
- WP8270019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Top rack front wheel broke.
Pulled out dishwasher. Took out old screws. Unsnapped end of rack slid new wheel in and attached to side. Very Very easy. It was great to get the part so fast and take care of this repair ourselves.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from North Manchester, IN
- Parts Used:
- WPW10199696
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Change detergent dispensor
Take 10 lower star srews from inside of door (5 per/side) that hold on front. Remove front door panel. Remove 6 screws in detergent dispenser and replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- J from HARPERSVILLE, AL
- Parts Used:
- WPW10195536, WP8531323, W10878507
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Water leak
I watched the instructional videos that showed how to replace the inlet fill hose/water inlet a couple of times. The repair was exactly as shown. No trouble at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Crystal from Stansbury Park, UT
- Parts Used:
- WP8558307
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I did not lock the cap good enough and it fell off and melted
I just placed the cap back on, it worked great, fit fine and so glad I found this part. I was thinking of ways to McGyver it, thinking it would be impossible to find a new part. Glad i fount this site and the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN C. from GIG HARBOR, WA
- Parts Used:
- WPW10199696
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
The soap dispenser would not work
After reading other posts I opened the dishwasher door put a support underneath it. Knowing that all the screws were not the same I carefully unscrewed them and placed them on a towel in order of extraction. After all the screws were taken out, I lifted the door up gently and lifted it out of its place and put it aside. Now I could see the hex screws holding in the soap dispenser. I then unscrewed the screws and place the frame aside. Next I gently pulled the electrical connector to the dispensing unit off. After locating a snap tab on top on the left hand side and one underneath on the right hand side, I gently lifted the tab and the dispenser unit moved slightly forward. After gently prying the lower tab on the right hand side the dispensing unit was loose. I just reversed the process to put things back together. I was not necessary to have any help taking things apart but it was very helpful having a second set of hands when we put it back together. Lining up the screws for the door was much easier with two people. After installation, I started the dishwasher to check for leaks. Everything was fine. Very satisfied to be able to repair/replace this unit without calling a tech. If you can change a spark plug on a lawnmower you can replace a soap dispenser on a dishwasher such as mine. Very quick delivery from parts source. Thank you.
Was this instruction helpful to you?
Thank you for voting!