GU2800XTVY2 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jon from Bend, OR
- Parts Used:
- WP8269209
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No power to dishwasher. Quit mid-cycle.
Pulled front panel and replaced door switch. Extremely easy but did not fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Beaufort, SC
- Parts Used:
- 8269144A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Drain hose leaking
I did not relize that the drain hose was in two parts. Naturally I ordered the wrong half. So after I relized my mistake, I re-ordered the correct part. Once the correct part was received the repair was easy and went well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Corona, CA
- Parts Used:
- W10258275
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The Power Was Completely Of The Dishwasher.
I opened yutube and noted the tips on how to fix specific problems with my dishwasher. That "steve" guy was very helpful. I tested the old bi-metal fuse with no flow and ordered a new replacement through partselect. The part arrived in one day and was fitted quickly. I used the teat meter to confirm that the fuse was ok before I installed it. The only problem that I had was identifying the part and number from a diagram which I did not have.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from WEST WARWICK, RI
- Parts Used:
- WPW10348269
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher would not drain. Pump was jammed with broken glass .
Turn off breaker to dishwasher.
Remove lower basket.
Drain any water using a wet vac.
Remove bottom cover plate. Should be 2 plastic screws using flat head screwdriver.
Should be able to reach pump. Turn counter clockwise to remove.
Disconnect plug wire on pump.
Install new pump by turning clock wise.
Reattach wire plug.
Run a wash cycle with empty dishwasher and check for leaks.
Replace cover plate.
Done.
Remove lower basket.
Drain any water using a wet vac.
Remove bottom cover plate. Should be 2 plastic screws using flat head screwdriver.
Should be able to reach pump. Turn counter clockwise to remove.
Disconnect plug wire on pump.
Install new pump by turning clock wise.
Reattach wire plug.
Run a wash cycle with empty dishwasher and check for leaks.
Replace cover plate.
Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Lebanon, CT
- Parts Used:
- W10518394, WPW10477552
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Dishwasher wouldn't work
Looked under machine, saw wire going to heater was burned off.Seal on heater failed, water leaked onto terminal, shorted and burned, ruined plastic terminal nut.Replaced heater and wire terminal, and nut, took minutes, works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Kernersville, NC
- Parts Used:
- 8269144A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
old hose possible leakage
put new hose on, very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothy from BILLINGS, MT
- Parts Used:
- W10727426
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
the tines in the upper basket of the dishwasher were falling apart
Removed the old tines by pushing out the clips on the end and then installed the new tines and applied clips - took 10 minutes worked slick and the washer basket looks to be brand.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- thomas from FULLERTON, CA
- Parts Used:
- 8193983
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
Upper rack not getting clean.
Watch your video about my dishwasher symptoms. Move water tube for upper rack to the right and release lower spray arm. Remove 4 clutch head screws from filter cover and remove. Dig out 10 years of undisolved soap and reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eva from Shalimar, FL
- Parts Used:
- W10518394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Heater element broken
I removed the lower front panel of the dishwasher to expose wheels and opened door and removed two screws holding washer to cabinet. After raising leveling feet pulled washer out to expose bnotton ow dishwasher. Removed the electrical wires form the heating element and removed screw caps holding the heaqting element in place. Removed the old element and inserted the new, then reversed process to get it back together. It was very easy to do following the instructions I received when I ordered the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from GRANDVIEW, MO
- Parts Used:
- W10648041
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
washer filled in when off..
replaced the valve
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- eugene from REVERE, MA
- Parts Used:
- WP8268961
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
door would fall down when unlatched
Removed the bottom plate/cover. Unscrew top from bracket. Lucky,had just enough room to pull washer out. Only 6 in. Sleeve had broken off. Needle nose plyers to unhook spring. Slide sleeve over hinge. Hard Part///. Pull spring back into place. with door shut. good luck.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from SARATOGA SPGS, UT
- Parts Used:
- 8193983
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The Spinner at the top of the dishwasher came off and would not stay on.
First of all I appreciate the instructions provided by this site when I selected the part I needed! The installation was so easy. I popped the end caps off of the top rack guides and removed the top rack. I reach in and popped the clips holding the top sprayer bar and gently pulled down on the sprayer bar enough to place the spinner button in the top of the sprayer bar. Then pressed the spinner on the bottom of the sprayer bar into the button I place in the top of the sprayer bar and reattached the sprayer bar to the clips. Put the top rack back on the guides and replaced the guide caps and it was finished. Easy fix thanks to this site great instructions!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from SAINT CHARLES, MO
- Parts Used:
- W10872845
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
New filter
Ordering the part was very easy. It shipped fast and delivered over 3 days. It fit perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dwight from KENT, WA
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
One of the old stops broke
Snapped the new stops on. It took about 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Westminster, CO
- Parts Used:
- W10258275
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The Dishwasher had a no power symptom
I researched the internet about this symptom on the Kenmore Elite Dishwasher and I found lots of people with the same problem. Everyone fixed it by replacing the Bi-Metal Fuse. I removed the old fuse and tested continuity and it was indeed bad. Once the new fuse arrived I tested continuity and it of course worked as expected, so that was a nice wipe of the brow. The new Bi-Metal Fuse came with a nice instruction manual. I also used a video from YouTube to help with the repair as well, but the included instructions were enough. The only thing that was not clear was the best way to attach the new wire since it was quite a bit longer than what was orginially there. So I ended up just folding it up and putting everything back together and it worked just fine. This repair was very easy as long as you are OK with cutting and stripping wires in a somewhat confined space and not being too worried that you might mess it up for good... :)
Was this instruction helpful to you?
Thank you for voting!