GU2800XTVQ1 Whirlpool Dishwasher - Instructions

A Mouse friend had seen fit to chew through the original drain line. I used my Model Number, and was able to order the correct part . It arrived the next day. The job itself is fairly straight forward. You will need to access the rear of the machine. This may include shutting off, and disconnecting the water supply line. (Adjustable wrench). Mine is under the sink, on the "Hot" side. You may also need to un-plug the unit. (recommended) . A pair of (Pliers) will be needed for the spring clamp.

Put new rack by old rack. Carefully remove a wheel assembly off old rack, then installed on new rack. Did this 3 more times. Then remove front tab clips off old rack & installed on new rack

The repair was easy. Getting the unit to slide out from under the counter was more time consuming.
After water and power is disconnected, tip the unit over onto one side to gain access to bottom. Look for two white composite plastic posts (insulators) about 2" long each with a single wire inside. Remove the two wire connectors then unscrew the insulators from the old heating element using an adjustable wrench. Inside the box remove the two metal element supports and pull out the old element. Clean and dry the area in and around the openings where the new element will be re-inserted. Carefully place the new element into the holes with the included new rubber washers. Re-install the two metal element supports on the inside of box. On the bottom, re-install the two insulators to the ends of the element, do not to tighten too much to avoid over compressing the rubber washers which could cause premature cracking. Reconnect both wires and check continuity from the door mircro-switch (white-violet) lead to the (white-red) lead on Electronic Controller connector #1 (P6). The circuit thru the element should be good if the Multimeter reads 10-35 ohms. Put the unit securely back under the counter and run a test wash. Works fine now.
I do recommend, if don't know how to use a multimeter or are concerned about accessing the electronic control box; contact a professional.

Removed the front panel of the dishwasher. Unhooked the electrical connection between the dishwasher and the dispenser, which was as easy as unplugging a cord from an electrical outlet. Removed the old dispenser and replaced it with the new one. Replaced the front panel. This was a super easy repair.

I turned off the power to the dishwasher, removed the kick plate, raised the front levelers, disconnected the electric to the appliance, turned off the water supply to the appliance, disconnected the water supply, disconnected the drain system from the garbage disposal, unscrew the appliance from the countertop, then I remove the appliance from underneath the counter. I then tilted the appliance back and then in screwed the plastic retainers that held the heater element in place, removed the old one, replaced it with the new one in reversed the whole process

I watched the video identifying the part and the procedure to make sure I could handle this. The phone attendant was also very helpful in making sure I ordered the correct part,which arrived in one day (amazingly). Everything was clearly described in the instructions and if you have done electrical work this would be relatively easy. You will need a specific screw driver bit to open the control panel but everything else is straightforward, just follow the instructions. Works perfectly now (I needed a new control panel about a year ago and Kenmore charged me $229 but it was just over a year since then....) PartSelect is a great service!

Looked at other side of top rack which still had the stop. Just had to orient the direction of the stop and push it firmly onto the rack arm. Took a couple tries, but it went in and locked. Works perfectly. Inexpensive and easy fix to to very annoying problem.

Replaced the switch, that did not fix it, but a new circuit card did

Simply made sure the cap was securely in place.

After bailing out the unit, filled filter hole with a moderate amount of Dawn dish washing detergent. Ran dishwasher twice to remove all Dawn from the unit. Had to bailout the water (and suds) from the washer both times. After the dishwasher finally drained I inserted the new filter..

The video included with this part is perfect. Unplug the dishwasher, take off the front trim piece, remove the drain hose from the pump, unclip the power, press the little clip that holds the pump in while turning it counter clockwise to remove. Then just do that in the opposite order to put the new one in. Just make sure you hear it click when you twist the new one on so you know the clip has engaged. Super easy.

Our Kitchenaid dishwasher was leaking so I called a repair service. I gave the model number and serial number over the phone and explained the problem. I was told the rubber gasket would need to be replaced. When the repairman came 5 days later he told me that the gasket needed to be replaced but he didn't have a new one on his truck. He ordered one and said he would be back in a week to repair the dishwasher. That took 10 minutes at the most. He then gave me a bill for $200.49 ($71.49 for the part and $129 for the labor)that I had to pay right then. I wrote him a check so he would leave and immediately called the repair company to tell them the price was outrageous and that I had never before paid for a repair before the work was done. I was simply told it was their policy. I then told them I was stopping payment on the check - which I did. I checked on-line for the part and found your web-site and the the part I needed for $27.62. I ordered it on a Monday, it arrived on Tuesday and my husband easily installed it that evening. Thank you, thank you, thank you!

I unscrewed the dishwasher from the counter (two screws under the countertop), and pulled it out about a foot so I could access the friction sleeve. I used a needle nosed pliers to slip a spring latch off the door. Then I slipped the new friction sleeve on and reattached the spring. Tested the door. Success! Super easy. About 5 minutes of work.

I did not relize that the drain hose was in two parts. Naturally I ordered the wrong half. So after I relized my mistake, I re-ordered the correct part. Once the correct part was received the repair was easy and went well.

I am a 61 year old woman and it took me a total of 2 min. max. Popped it into place and pushed in button that holds it..Taa Daa...perfect!