DU1345XTVB1 Whirlpool Dishwasher - Instructions

I just placed the cap back on, it worked great, fit fine and so glad I found this part. I was thinking of ways to McGyver it, thinking it would be impossible to find a new part. Glad i fount this site and the part.

Make sure you order 2. One on each side

I simply pulled out the old gasket and pushed the new one in with my fingers. I had to trim about an inch off the length with a utility knife. The seal is nice and tight now and we have no more water leakage.

I watched the video and this was the easiest repair ever. Took longer to disconnect and reinstall than it did to change out the pump. Highly recommended watching the video

I snapped on the new part onto the track. It was that easy! :) Thank goodness the part was available from Part Select!
T. Edwards

Was able to replace and repair without taking the dishwasher out. Thermostat is behind and to the left of the power junction box. Has 2 wires going to it. It is up against the bottom of tub. I used an angled mirror to see what I was doing. 1 small screw to detach and pull down thermostat. Be sure power is off before you start. Also reprogrammed defaults. Hit any button 1-2-3, 1-2-3, 1-2-3, fast and close door. Let it sit 15 min to run and re-set defaults. Now I have heat and dry dishes.

Shut the power to the dishwasher off. Pulled unit out from under the counter top and raised the left hand side up for easy access. Disconnected the wiring, undid the clips, turned counter clockwise and removed. Reversed the order for installation and Connected the power. Ran several cycles successfully. Problem fixed. Burnt out water pump. Good as new if not better so far. Easy item search, Fast Shipping, Quality Part, Fair Pricing. Thank You Partselect.com

The upper spinner was laying in the top washer basket. I went online but no help was avaiable. Went to store where we purchased dishwasher and they gave me part number to order but not online I had to call to order. Part arrived in about three days. I took two screws loose on the top of dishwasher removed broke retainer to put new retainer in but I drop it into dishwasher so you have to me very careful
so I tried to order just the retainer but is not sold by it self. Had to order whole new kit. Other than that it is easy dishwasher runs like a new one.

Remove front door panel, replace B-metal fuse.

Unscrewed the top of the dishwasher from the counter top and slid the appliance out part way in order to reach the door spring. I loosened he spring from the bracket then slid the sleeve over the bracket. I reattached the spring to the bracket, slid the dishwasher back in and screwed it to the top just like it was prior to removal. Easy as pie.

The repair was really easy. First disconnected electricity staring with fuses and removing wires from dishwasher, then disconnected drain hose and water hose. Pulled it out and removed pump turning clockwise no need for tools and same way installed new one. Very easy

Pulled everything out the front, and dug down to find a thrashed chopper assembly (like a little garbage disposal). The previous owner just tossed anything in; pop tops, plastic cutlery, etc.
Didn't pay attention to the exact installation of the chopper as I pulled it out, but, it turns out that it only goes in one way.
Used pictures and instructions I found online as a guide and didn't have any issues.
Replaced the check valve because it isn't expensive and I was in the neighborhood.

Removed first part of the broken part from the top rack of the dishwasher from below.

Removed the screw from the bottom of the sprayer arm to release the second half of the broken part.

Threaded new part in sprayer arm and replaced screw.

Attached part to top rack of dishwasher from below. This part was difficult. (The part appeared to be a little larger than the original.) It was a two person job, one person pushing down on the rack and the second pushing upwardand inward on the part it click to click it into place. Dishwasher now works great.

This procedure assumes that the DW water connection and drain are flexible. Remove Phillips head screws (2) mounting top front of DW to underside of counter. Grasp door and gently coax DW outwards approximately 1 foot. WEAR SAFETY GOGGLES. On RHS check lower end of door spring and note in which notch the spring sits. On RHS, grasp white plastic connector ("hinge bushing", with spring looped around one end), stretch the spring while carefully lifting other end of connector up, out of slot in door hinge lever. Pry door hinge lever 1/8" away from DW body while sliding friction sleeve over its end. Work friction sleeve past hinge hook, past wider section, into narrower slot (about 2" from end of hinge hook). Raise door to closed position. Insert and hold lower (90 degree) end of spring into the same notch that it was originally in (mine was in the 5th from the front). Loop the door end of the spring into one end of the white plastic hinge bushing, then insert the other end of the bushing into the door hinge lever's hook while stretching the spring. It does not require much strength. CAUTION: If the lower end of the spring is not properly inserted and held in the notch, it can pop out and possibly injure you! Repeat for the LHS. Push the DW back in place, and reinstall the two mounting screws.

I followed the PartSelect video to replace the feed tube assembly with spinner and the spray arm seal for the middle wash arm. Washing performance was better, but a couple weeks later the dishes on the bottom rack suddenly stopped getting clean. I decided I probably needed a new chopper assembly, which is identified by PartSelect as the cause of problem for 48% of the cases of dishes not getting clean. Before ordering the chopper assembly, however, I followed the video about how to replace the chopper assembly to determine whether the chopper assembly seemed to be worn out (the video shown at https://www.partselect.com/PS11722146-Whirlpool-W10083957V-Chopper-Assembly.htm). It was worse than I anticipated. I found the holes of the chopper assembly screen blocked by food, and the spinner in front of the screen had broken apart. In addition to finding the pieces of the broken chopper assembly, I discovered a treasure chest of debris, including about 8 pieces of broken glassware, 3 twister ties, a half-inch button, a 3/4-inch screw, and dozens of small pieces of metal. I poured water into the area and used a kitchen baster to suck out the water with all the pieces of debris, finishing the clean-up with paper towels. I ordered a new chopper assembly to replace the broken one, and the part arrived in under 48 hours. I relied on the same video to install the new chopper assembly. The only tricky challenge was getting the new chopper assembly back into place. I first tried needle nose pliers in two sizes, as recommended in the video, but what worked much better for me was using two chop sticks that were each about 1/4 inch square from top to bottom. Needle nose pliers are slanted, but the chopsticks did not vary in thickness and separated the screen from the spinner an even distance apart, making it easier to get the gear shaft on the chopper assembly to align in a straight line with the gear shaft on the pump motor. I also rotated the two gear shafts so the gears of the chopper assembly would mesh correctly with the gears of the pump motor shaft. The video cannot show that step very well because the man's hand blocks vision of how exactly to fit the chopper assembly into place. The video also fails to warn about possible debris around the chopper assembly and to explain how to clean out the debris. After finishing installing the chopper assembly my 14-year-old dishwasher cleaned my dishes as well as a new dishwasher. I spent a total of $110.24 on parts and shipping and invested a couple of hours total. The alternative would have been to spend $800 on a new dishwasher or wash dishes by hand. I am very, very happy with the outcome.