DW524L1ASS0 Whirlpool Dishwasher - Instructions

I am NOT an appliance technician. I am simply a somewhat handy homeowner. Removal of outer door panel requires removal of two screws from inside the top of the door assembly at the latch, as well as all of the obvious mating screws from around the perimeter of the inside of the door assembly. Use a #15 torx driver bit. Pull top of panel out (away from the machine) by maybe two inches, then lift the outer panel up to clear the bottom end of it from the lower positioning brackets. DO NOT lever the top of the panel outward. Keep it close to the inner door. It may take bit of an upward tug to dislodge. Careful here - the outer panel will simply fall free. Two wire pigtails that are connected to components on the inner door are short, so be careful not to strain them after dislodging the outer panel. One is connected to the dispenser. Disconnect both as to provide good clearance for the component replacement. The main wire harness is of sufficient length as to not cause a problem. The six 3/16 hex head screws holding the dispenser in place are easy to remove. There are two small sheet metal tabs that keep the device in place after the screws are removed, but a rectangular mounting frame or bezel will come off, along with the little black curtain that protects the unit. The tabs are at upper left and lower right at the perimeter of the opening in the inner panel. They must be levered gently as to allow the dispenser to push inward for removal. After removal, spend some time cleaning the inner surface of the inner panel as to ensure that the new device will make a watertight contact when fastened in place. Bend the tabs slightly back to an inward position, and install the new dispenser with the socket and motor to your left as you look at it from outside the machine. It clicks in to place and stays put. The bezel mounts only one way (in terms of being upside down) and the flat surface must be toward the inner door. Re-positioning the little black curtain is tricky but if you follow the marks in the material from the previous mount it should work out OK. Tighten the screws evenly as to ensure a good seal. Move the outer cover closer and reconnect the two plugs. Use an object to wedge the inner door open by a few inches, and lift the front panel such that you can position it and slide it back down on the inner panel as to re-engage the lower holding brackets. This keeps the bottom of the panel in place during the reassembly. Now for the fun part... The upper end of the outer panel has to be positioned just right against the inner panel in order to seat the two long screws that straddle the latch assembly from the inside. You'll need clamps, or two people. There's a flat rubber seal on the top edge of the inner door. See that it is seated properly, and then that it becomes covered by the outer panel. If one person firmly holds the panels precisely in position, then the other person can install the screws to a point of being mildly snug. The other two longer screws go in the top-most holes at the upper/outer corners of the door assembly. Place them next. From there, you can carefully replace all the rest of the screws. Only after all of the screws are in place should you make all of them tight. You're done.

I opened yutube and noted the tips on how to fix specific problems with my dishwasher. That "steve" guy was very helpful. I tested the old bi-metal fuse with no flow and ordered a new replacement through partselect. The part arrived in one day and was fitted quickly. I used the teat meter to confirm that the fuse was ok before I installed it. The only problem that I had was identifying the part and number from a diagram which I did not have.

Be sure to shut off power at circuit breaker and disconnect drain and water supply. Remove the dishwasher from the cabinet, lower it on its side. Remove three electrical connections from motor to various sensors. Remove three plastic wedges that secure the motor gasket to make a tight seal. The motor pops into the body of the dishwasher for removal. The replacement motor goes in just as you took it out. It took two people to set the motor right to ensure the good seal on the gasket for re-installation. Then turn it back upright and secure it in place. Couple suggestions, be sure to have ample towels around for leakage from water and drain lines. Be sure to cover the bottom of the dishwasher during disassembly and reassembly of the wash manifold. I dropped a screw in there and it took me some time to fish it out.
All in all, it went well. Don't pay a plumber for this job. I'm a clod and if I did it, you can.

I researched the internet about this symptom on the Kenmore Elite Dishwasher and I found lots of people with the same problem. Everyone fixed it by replacing the Bi-Metal Fuse. I removed the old fuse and tested continuity and it was indeed bad. Once the new fuse arrived I tested continuity and it of course worked as expected, so that was a nice wipe of the brow. The new Bi-Metal Fuse came with a nice instruction manual. I also used a video from YouTube to help with the repair as well, but the included instructions were enough. The only thing that was not clear was the best way to attach the new wire since it was quite a bit longer than what was orginially there. So I ended up just folding it up and putting everything back together and it worked just fine. This repair was very easy as long as you are OK with cutting and stripping wires in a somewhat confined space and not being too worried that you might mess it up for good... :)

removed rack
removed one screw
removed old seal
installed new seal
installed screw

Removed old part and replaced with new part

disconect water supply and drain hose, unscrew 2 screws hoding front of dishwasher to countertop, slide dischwasher out so you can tip on its door and remove 1 screw hidden behind plastic shield and pull motor out install in reverse order.

Removed the old hose, after loosing metal looking rings. Installed new hose ad finally tight firmly the looking rings, using wrench and socket.

Remove the top 6 screws and replace the control board

Snapped the new stops on. It took about 2 minutes.

Removed old tine rows and replaced with the new parts. No tools were needed. Each was replaced one at a time so the old ones could serve as a model for how the new ones were inserted and attached. Not much more complicated than changing a light bulb. Parts appear to be good original equipment quality but quite pricy for these very simple pieces.

Replacing the float switch was fairly easy and straight forward. removed old using adjustable wrench and replaced.

Replacing the door links was not difficult except I needed to pull the dishwasher out and had to disconnect the water line.
reconnecting the water line was the time consuming and frustrating part. Once that was hooked up and tested, i pushed the dishwasher back in place and all is good again.

Hardest part was pulling dishwasher away from cabinet, making sure to not disturb water and drain line. I replaced both door springs which are on the two sides and attached to the dishwasher frame towards the back. This necessiatated pulling the dishwasher about 2/3 out of cabinet. After attaching both springs to frame, replacing the balance kit was a breeze .One screw to remove and then replace with new pulley unit. Attach the supplied cord with attached fittings to spring and then around two pulleys and mounting point on frame. Done . Push dishwasher back into cabinet, reattach two screws to underside of counter. Probably did not require new springs as they seem heavy duty and were not broken upon examination but ordered them also and replaced just in case. Most problem would be with broken cord in balance link kit

The video included with this part is perfect. Unplug the dishwasher, take off the front trim piece, remove the drain hose from the pump, unclip the power, press the little clip that holds the pump in while turning it counter clockwise to remove. Then just do that in the opposite order to put the new one in. Just make sure you hear it click when you twist the new one on so you know the clip has engaged. Super easy.

First of all I appreciate the instructions provided by this site when I selected the part I needed! The installation was so easy. I popped the end caps off of the top rack guides and removed the top rack. I reach in and popped the clips holding the top sprayer bar and gently pulled down on the sprayer bar enough to place the spinner button in the top of the sprayer bar. Then pressed the spinner on the bottom of the sprayer bar into the button I place in the top of the sprayer bar and reattached the sprayer bar to the clips. Put the top rack back on the guides and replaced the guide caps and it was finished. Easy fix thanks to this site great instructions!