DU1014XTXD3 Whirlpool Dishwasher - Instructions

Used bowls in upright position in upper shelf determining no water to upper shelf after running in rinse cycle. Added a cup of Vinegar in rinse cycle. Performed bowl test in upper rack & still no water in bowls. Dismantled inside of unit by removing both spray arms & found lower seal deteriorated & upper seal in need of replacing. Replaced seals & redid bowl test & found no water getting to top rack still. Found utube vid showing removing garbage disposal portion of unit. Requires removing screen in bottom of dishwasher. One screw attaches garbage disposal cover. Found non food items & food by broken garbage disposal. Repaired disposal, removed debri & reinstalled all components. Redid bowl test in upper shelf & bowls were overflowing!!????Dishwasher works GREAT now & can hear garbage disposal operating along with massive water being sprayed!!!

I took the valve off and actually hooked 110 volts to the vale and tried to blow through it and it would not let air pass through it. I replaced the the new valve in about 15 minutes and it works fine

Followed directions from YouTube video.

Bought the new cap, took it out of package, installed.

Ordered a new pump (after a online diagnosis). Followed the instruction video on the website...also took the time to replace the discharge hose due to residue buildup...tested dishwasher (one cycle). Slide dishwasher back into opening....DONE. Works perfectly. THANKS

At first, I figured the noise was coming from underneath, and took off the bottom front plate. I noticed there was a leak from the center of what I later learned was the "pump" assembly. So I unplugged the dishwasher, disconnected the water and drain from under the sink, unscrewed the screws holding it under the counter, and pulled it out from under the cabinet. Then I laid it on its back, and realized where the leak was coming from. At this point, I thought the noise had been coming from the motor. So I detached the motor (required use of a socket, and realized it was "free", so thought the problem must be further up inside. Reached my fingers in where the motor mounts and found part of the chopper assembly. The "chopper" had torn itself free from the screen. Realized at that moment I needed to disassemble the pump from the top. Took off water distribution system, bottom water rotor, pump plate (required use of "star" screwdrivers, two different sizes), foreign object plate, and chopper assembly cover. Getting the chopper assembly cover off was hard; had to pry it with sharp l-shaped poker; it was adhered with calcium deposits. Finally got it off, found rest of chopper assembly (screen with hole in the middle where chopper had been), ordered chopper from PartSelect, took 3 days, installation was easy, the reverse of removing it. (It is not necessary to remove motor to replace chopper assembly.) However, it is still leaking from the bottom, and I'm at a loss as to how to fix that.

Long story short, noticed one of two leaks and came to conclusion there is no workaround since sump pump gasket seems to be hermetically sealed to sump pump. Which is understandable because of water in area. Wife helped by soaking other parts that were removed and replaced, because of calcium buildup. Which we hope will extend life of dishwasher. I put 1 to 2 hours because I took my time and made sure all parts fit correctly and were back in their original place. Didn't want to take any chances in not covering bases. I am no expert, but definitely a diy'er. I believed I saved myself anywhere from $200 to $300 in labor costs by repairman. By the way, thanks Parts Select your info and site are awesome!!! The second part I had to order was the water inlet valve and your phone representative was a big help over the phone, please don't eliminate those positions. Overall total price of parts approximately $130 w/delivery. Well worth it, since a brand new halfway decent dishwasher starts at $550.

The repair was easy, no instructions with the part. I had a bad leak the first go round, found out that I did not have it centered with-in the indentation on the door panel, so I got to install it twice.

Very simple just remove the rakes and then unscrew the covers and pop out the old chopper assembly and replace with the new and then just put all cover back and it works great.

Rubber friction sleeves on each side of the door provide resistance to prevent the door from quickly opening when unlatched. Over time the friction sleeve may crack and fail. Two friction sleeves are required for repair. Install a new sleeve on each side of the dishwasher door near the spring connector at the bottom.

Open dishwasher door.

Remove the screw from the left and right bracket at top of dishwasher door opening. Brackets secure the dishwasher to the countertop.

Gently pull the dishwasher forward to expose the door spring on each side of door at bottom.

Unhook the plastic spring connector from the left door spring hook by pulling the connector slightly forward and lifting from the door spring hook. Remove the old friction sleeve if still in place by sliding over the door connection hook. Discard the old sleeve.

Insert the new friction sleeve over the door spring connector hook and push until the friction sleeve is in position completely past the spring hook. Reconnect the plastic spring connector to the door hook.

Repeat for right side of door.

Close and latch the dishwasher door. Unlatch the door. The door should remain in the nearly closed position held in place by the friction sleeves.

Slide the dishwasher back to the original position under the counter top.

Insert the screws in the top brackets to secure the dishwasher.

Very easy to remove the broken one and just clip in the new one.

Fast,smooth,easy.

Recently bought a whirlpool dishwasher, the dishwasher was converted to a portable dishwasher and they did not use the cord application power cord so they machine was blowing our breaker, instructions were very simple and installation was easy!

Just click in, you can basically do it with your eyes closed

Replaced the detergent dispenser using the directions on the shipping notice.