7GU2300XTVS2 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Frances from Longmeadow, MA
- Parts Used:
- W10542314
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
worn gasket was fraying at bottom of door, leaking
just pulled old gasket out. New gasket took 2 attempts to fit in properly, but simple to do. Very easy to press into groove. Fit like a glove! Website drawings made choosing part very easy, thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Derek from Chubbuck, ID
- Parts Used:
- W10542314
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Worn out door gasket
Easy to do. Less than fifteen minutes total and only tool required was a screw driver. Simply pulled out the old gasket by hand and then pressed in the new one with the screw driver. Anyone could do this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from WESTERVILLE, OH
- Parts Used:
- WP8565925
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rollers broke off top rack assembly
Replacement parts from factory installed using u tube support video
Also replaced stop ends for top rack by removing old clip in to push down and lined up to secure in slots at end of rack, notice new plastic parts are installed by pushing hardware into slots downward until they clip into place
Also replaced stop ends for top rack by removing old clip in to push down and lined up to secure in slots at end of rack, notice new plastic parts are installed by pushing hardware into slots downward until they clip into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nick from Littleton, CO
- Parts Used:
- WPW10334457
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Pump motor would not start
I did not get to repair my dishwasher using the part supplied by Partselect.com. I pulled my dishwasher out and found that the connector had fallen of the capacitor during installation. Happy to say that I returned the part for a full refund minus the shipping. Have bought from them before, and will again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois from HUDSON, NC
- Parts Used:
- WPW10348269
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
pump not working
Looked on you-tube and it was so easy. Pump on bottom right. unplug pump and do a halfway turn. Plug the new one up and place the pump on, and turn halfway and its on. START your dishwasher
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from WESTON, FL
- Parts Used:
- WPW10503548, WP8558307
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Rinse Aid Cap
I ordered the cap for my kitchen aid dishwasher and it is too small.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reid from ALPHARETTA, GA
- Parts Used:
- WPW10337934, W10518394
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dishes were not drying properly
Did the repair, but needed one extra step not described in video:
I followed the directions on the PartSelect Youtube video - very helpful! I do believe the heating element was the original culprit, as it had a "burn" area about the size of a dime that caused it to almost break into two parts. Obviously a point of failure.
BUT - after replacement, it still did not solve the problem of the dishes not drying.
After much web searching, I tried the diagnostic mode on the dishwasher, and that did a hard reset of the logic board and FIXED the problem.
So in all, it required both a new heating element AND a hard reset via diagnostic mode.
I followed the directions on the PartSelect Youtube video - very helpful! I do believe the heating element was the original culprit, as it had a "burn" area about the size of a dime that caused it to almost break into two parts. Obviously a point of failure.
BUT - after replacement, it still did not solve the problem of the dishes not drying.
After much web searching, I tried the diagnostic mode on the dishwasher, and that did a hard reset of the logic board and FIXED the problem.
So in all, it required both a new heating element AND a hard reset via diagnostic mode.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from FORT MYERS, FL
- Parts Used:
- WPW10348269
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Dishwasher would not drain properly due to broken impeller in the pump. Could hear and feel vibration thru pump body.
Followed the easy how-to video from PS. It was as easy as changing a light bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from SKYKOMISH, WA
- Parts Used:
- WPW10348269
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
dishwasher would not drain
Follow the u tube instruction. Replacing the pump was very simple and easy. The hard part was getting the dishwasher out of the cabinet and back in again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lester from Aguanga, CA
- Parts Used:
- 8193983
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Top spinner kept coming off due to worn bushing
I Removed the upper wash rack by removing locks on each front slide of rack. I laid a towel in the bottom of the washer to keep anything dropped, retrievable. I then removed the top screw closest to the spinner location. I then carefully pulled down on the mounting, which exposed the bad bushing lock. I removed the old bushing lock and replaced with new one. I then replaced the spinner with a push with one hand while holding the bushing in place with the other hand. You will feel a snap as all goes into place. Make sure new spinner spins freely. Now reinstall removed screw. Do not over tighten. Now reinstall lower rack, carefully aligning water feed in rear of washer, and making sure all rollers are back in sliding rack. Reinstall locking tabs onto sliding rack. Now slide out rack, it should not come off slider. Important: now remove the towel in the bottom of the washer. If left in place, you will have a fire during the drying cycle. Close the door and test your washer through a cycle. I felt confident and did a load of dishes. If all went well, spinner should be in place, not in the bottom of the washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from SEATTLE, WA
- Parts Used:
- WP661566
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Heating element not heating for both wash and dry.
Put in both a new element and thermostat. Did not fix problem. Using an ohm meter I did not measure any voltage to the thermostat. Suspect it’s a problem in the control unit, and decided to replace dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from HIGHLAND MLS, NY
- Parts Used:
- WPW10348269
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher had a pool of water in it after using it.
Soak up the water in the dishwasher with an old towel. Removed the cover under the dishwasher. Found the pump and twisted it off anti clockwise. Replaced with the new pump. Run a quick cycle, to make sure it pumped out all the water. My wife has used it several times since without any issues.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from BOISE, ID
- Parts Used:
- W11157084
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Upper rack roller was broken, and basket would drop
Followed the video from PartSelect. I've used PartSelect for replacement parts three times now, and their videos do an excellent job of showing how to do the repair.
It's worth noting that some DIY repair videos may not be easy to find - PartSelect's customer service department is really good at finding them and sending links. If you don't see a video, call and ask.
It's worth noting that some DIY repair videos may not be easy to find - PartSelect's customer service department is really good at finding them and sending links. If you don't see a video, call and ask.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from NEW CARLISLE, IN
- Parts Used:
- WP8558307
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cap had loosened and fell onto heater coil and melted.
Screwed in new cap
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jason from Orrville, OH
- Parts Used:
- W10258275
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
no power to control panel
really easy to repair... no power to control panel but had power from breaker box. Followed directions that came with part, self explanatory, took 10 mins.
Was this instruction helpful to you?
Thank you for voting!